Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
058-720-039
RECORDING REQUESTED BY: AND WHEN RECORDED MAIL TO: BUTTE COUNTY BUILDING DIVISION 7 COUNTY CENTER DRIVE OROVILLE CA 95965 COPY of Document ,Recorded 05 -Mar -2003 2003-0013830 Has not been compared ath �. original — BUTTE COUNTY RECORDER SPACE ABOVE THIS LINE FOR RECORDER USE ONLY NOTICE OF MANUFACTURED HOME (MOBILEHOME) OR COMMERCIAL COACH, INSTALLATION ON A FOUNDATION SYSTEM Recording of this document at the request of the local agency indicated is in accordance with California Health and Safety Code Section 18551. This document is evidence that such local agency has issued a certificate of occupancy for installation of the unit described hereon, upon the real property described with certainty below, as of the date of recording. When recorded, this document shall be indexed by the county recorder to the named owner of the real property and shall be deemed to .give constructive notice as to its contents to all persons thereafter dealing with the real property. DON M. HEIL AND CAROL S. HEIL REAL PROPERTY OWNERILESSOR, 1970 N. LESLIE ST. # 3472 MAILING ADDRESS PAHRUMO NYE NV 89041 CITY COUNTY STATE ZIP 5006 BIG BEND RD. INSTALLATION MAILING ADDRESS, IF DIFFERENT OROVILLE BUTTE CA 95966 CITY COUNTY STATE ZIP SAME UNIT OWNER (if also property owner, write "SAME") MAILING ADDRESS CITY COUNTY STATE ZIP UNIT DESCRIPTION BUTTE COUNTY BUILDING DIVISION LOCAL AGENCY ISSUING PERMIT and CERTIFICATE OF OCCUPANCY 7 COUNTY CENTER DRIVE MAILING ADDRESS OROVILLE BUTTE CA 95965 CITY COUNTY STATE ZIP 02-3232 530 538-7541 BUILD G PERMIT NO. TELEPHONE NUMBER =M�6L& 3_'5'6'3 ATURE OF LOCAL AGENCY OFFICIAL DATE EXECUTIVE HOMES DEALER NAME (if not a dealer sale, write "NONE") 92081 DEALER LICENSE NO. ' FLEETWOOD 2003 WOODLAND PARK 4453 A MANUFACTURER'S NAME DATE OF MANUFACTURE MODEL NAMENUMBER CAFL217A/B26214-WP13 45'4" X 26'8" PFS0795896/7 SERIAL NUMBERS) LENGTH X WIDTH INSIGNIA/LABEL NUMBER(S) REAL PROPERTY LEGAL DESCRIPTION - ASSESSOR'S PARCEL NUMBER AT # 058-720-039 See 4A(- heel HCD FORM 433(A) REV. 8/91 WHITE = County Recorder CANARY - HCD PINK - Applicant GOLDENROD- Building Dept. t VFOUNDATIONr.SYSTEIVI -CERTIF_=ICATE OF OCC PANCY = _ F BUILDING PERMIT NUMBER: 02-3232 Address or location of unit: 5006 BIG BEND RD., OROVILLE CA 95966 Legal Description of Real Property: AP # 058-720-039 SEE ATTACHED ` (x) Mobilehome/Manufactured Home , O Commercial Coach Has been affixed to the real property above by installation on a foundation system pursuant to Health and Safety Code Section 18551. • . 4 r i a Owner's name: DON M. HEIL AND CAROL S. HEIL ' Owner's address: 1970 N. LESLIE ST., # 3472 PAHRUMP CA 89060 INSIGNIA OR HUD NUMBER: PFS0795896/7 SERIAL NUMBER OR V.I.N.: CAFL217AJB2614-WP 13 MANUFACTURER'S NAME: FLEETWOOD YEAR: 2003 OFFICIAL APPROVING INSTALLATION: DATE: 3-5-03 PHONE: (530) 538-7541 H.C.D. 513C 11/04/02 11:29 BIDWELL TITLE 4 530'891 8753 Escrow No. 301277-SML iron order No. 00301277 EXHIBIT ONE PARCEL ONE: N0.598 P005 _ Parcel 1, as shown on that certain Parcel Map, filed in the Office of the Recorder of the County of Butte, State of California, on July 30, 1973 in Book 46 of Maps, at Page(s) 64. . Excepting therefrom all hydrocarbons and minerals now "or at any time hereafter situate and thereunder and which may be produced therefrom together with the free and unlimited right to mine, drill, bore, operate and remove from beneath the surface of sold land at any level or levels 100 feet or more below the surface of said land for the purpose of, development or removal of all hydrocarbons and minerals situated therein or thereunder at producible therefrom. PARCEL TWO: A right of way for road and public utility purposes over the Southerly 30 feet of parcel 2, as shown on that certain parcel map filed in the office of the recorder of the County of Butts, state of California on July 30, 1973 in gook 46 of maps at page 64. PARCEL THREE: Aright of way for road and public utility purposes over a Stripbf lend 30 feet in width lying Southerly and Easterly of and adjacent to the Southerly and Easterly line of Parcels 1 and 2 as shown on that certain parcel map filed in the office of the recorder of the County of Butte, State of California on July 30, 1973 in Book 46 of maps at page 64. FILE No . 234 02/18 '03 PH 04:21 I D :EXECUTIVE HOMES FAX : 530 891 8753 PAGE 2 1 aTNTBf I STATE OF CALIFORNIA ( NUMBER: BUSINESS, TRANSPORTATION AND HOUSING AGENCY ' DEPARTMEN'T OF HOV$ING AND COMMUNITY DEVELOPMENT DIVISION OF CODES AND STANUARDB 8697416 I MANUFACTURED HOUBiNG PROGRAM MANUFACTURER CERTIFICATE OF ORIGIN DIBTRIBUTDN: ORIGINAL IPINK) FORWARD TOAmAEPIRT.I.CT VNTORY REDITOR. UNLESS THERE 18 NONE. THEN FORWARD TO THE PURCHASER IDFALER OR TRAN8FEREE), COPY 7 (WHITE) FORWARD TO AT P.O. DO% 1828. SACRAMENTO. CA 85812.1928. WITHIN FIVE )Ti) DAYS Of RELEASE. COPY Z (YELLOW) OEIIVERTO'TNBPORTF.R TO ACCOMPANY THE UNIT TO ITS OESTINATION. COPY 3(GOLOENROO) TO BE RETAINED 8Y THE MANUFACIURF"R. NCD 483.0 • SWa I • (7/67) ❑ CHECK IF THIS IB A DUPLICATE MCO -ENTER ORIGINAL MCO NO. MANUFACTURED HOME OR ML(L II -UNIT MANUFACTURED u�Xg FOUGING NUMBER OF 2 r LJ SFD (SINGLE FAMILY DWELLING) ❑ MUMH (MULTI -UNIT MANUFACTURED HOUSING TRANSPORTABLE SECTIONS WM�ERQIAL COACH: OCCUPANCY GROUP MANUFACTURER NAME: MANUFACTURER LICENSE NUMBER: FLEETWOOD HOMES OF CALIFORNIA, INC. 9534 MAgtFVjL1%�fMRWSAVjE . SUC36ESIED RE'T'AIL PRICE: DO BOX 1308 WOODLAND....:..' :.. ........ ..CA..,,..,.....,...95776 ....... .. Street CII Slate ZT MANUFACTURER TRADE NAME: MODEL NAME AND/OR NUMBER: DATE OF MANUFACTURE: WOODLAND PARR 4453A 2003 01/03/2003 NAME OF DEALER OR TRANSFEREE (OWNERSHIP TRANSFERRED TO); CALIF. DEALER NUMBER OR DATE OF TRANSFER: SECURITY M/H SHOW/NORTH, INC. TRANSFEREE DESIGNATION: DBAy EXECUTIVE HOMES 92081 01/03/2003 DEALER OR TRANSFEREE ADDRESS: 3042 ESPLANADE CHICO CA 95973 fitraet CII Slate(ZIP) INVENTORY CREDITOR NAME: BOMBARDIER CAPITAL INC INVENTORY CREDITOR ADDRESS: 261 MOUNTAIN VIEW DR COLCHESTER VT 05446 9uset CI (S to) (ZIP) SECTION MANUFACTURER AERIAL NUMBER NCD IN810NIA OR NUI) I ARF,1.. N(IMRER 1ANGTI1 WIDTII WEIGHT 1-6 INCHEB INCHES POUNDS 1 CAFL217A26214-WP13 PF00795096 544 160 19,460. •2 CAFL217B26214-(SP1) PF90795897 544 160 16,600 TRANSPORTER NAME: R TRANSPORT TRANSPORTER ADnRFBe: P 0. BOX 179 suee DURHAM GI state(ZIP)95938 DESTINATION FOR UNIT VESCHIBEU ABOVE: NAME(sliest) Cit Bible I ce111fy under pepelly of pe.)ury uAdar the laws of the State of California that I)ta above Iealtr we Itue wtd C-110. Etiewtedan 01/03/2003 at WOODLAND YOLO CA ( au) .1 (Camdy) (state) BIONATURE OF AUTIIORIZED AGENT; DIBTRIBUTDN: ORIGINAL IPINK) FORWARD TOAmAEPIRT.I.CT VNTORY REDITOR. UNLESS THERE 18 NONE. THEN FORWARD TO THE PURCHASER IDFALER OR TRAN8FEREE), COPY 7 (WHITE) FORWARD TO AT P.O. DO% 1828. SACRAMENTO. CA 85812.1928. WITHIN FIVE )Ti) DAYS Of RELEASE. COPY Z (YELLOW) OEIIVERTO'TNBPORTF.R TO ACCOMPANY THE UNIT TO ITS OESTINATION. COPY 3(GOLOENROO) TO BE RETAINED 8Y THE MANUFACIURF"R. NCD 483.0 • SWa I • (7/67) ' STATE 01' CALIFORNIA 1iTOr BUSINESS, TRANSPORTATION AND IIOUSING AGENCY ,g� •• DEPARTMENT OF HOUSING AND COMMUNITY DEVELOPMENT d DIVISION OF CODES AND STANDARDS • REGISTRATION AND TITLING PROGRAM STATEMENT OF FACTS This unit is a: 0 Mobdehome ❑ Commercial Coach ❑ Floating Home ❑ Truck Camper Decal (License) No.(s) Trade Name y�S 3 A I/We, die undersigned, hereby state: Dealer Report of Sale # Serial No.(s) The Above .Described Unit Has Been Placed On An Approved Foundation System In Accordance With 18551 A Of The Health And Safety Code. I/We further agree to indemnify and save hamiless the Director of Housing and Community Development, Slate of California, and subsequent purchasers of said unit, for any loss they may suffer resulting from registration of the above-described unit in California, or fi-om issuance of a California certificate of title covering die same. I/We certify under penalty of perjury that the foregoing is true and correct. Executed on lal ) at (Date) (C.ity) (State) Signa (s) Printed name s) 'Exe6aj-, t)p— #nyVte_9 Address �3�Ya` WAI ✓f' d � c.t� City ( t ,State FICD 476.6 (REV 12/00) la 11/20/02 16:16 BIDWELL TITLE 4 530 891 8753 RECORDING REQUESTED BY: Fidelity National Title Company of California Escrow No, 301277•SML Tile Order No. 00301277 When Recorded Mail Document and Tax Statement To: Mr. and Mrs. Don M. Heil 691-460 Tara Way SUSanville, CA 96130 GRANT DEED 02: N0.987 P002 1 9'99-0tb4'y`859 ,orded I Rix FEE 10.00 1 Records I TRX 10.45 _Y_tlf J.ORiiBBS 1 I corder I V DIOLKI l I stent i Maureen 12 -Nov -1999 I page 1 of 2 TH The undersigned grantorls► derdarels► Documentary tra wer tax is $10.45 I X 1 computed on full value of property conveyed, or I 1 computed on full value less value of liens of encumbrances remaining at time of sale, I ► Unincorporated Area City of unincorporated area of the Cq0'- FOR A VALUABLE CONSIDERATION. rcelpt of which Is hereby acknowledged. Roger J. Boutin, A Married Man dealing with his Sole and Separate Property hereby GRANTISi to Don M. Heil and Carol S. Heil, husband and wife the following described real property in the unincorporated area of the County of Butte, State of California: SEE EXHIBIT ONE ATTACHED HERETO AND MADE A PART HEREOF DATED: November 2, 1999 STATE OF CALIFORNIA COUNTY OF ('Qljjg,� � ON fiv e before me, Roger. outin -c4���� to A personally appeared -OROGER J. BO N* personally known to me (or proved to me on the basis Of sa;Z*6 tory evidence) to be the persono whose namesubscribed to the within instrument and acknowle ad to me that(S1sfAlt* executed the same i his *id*r authorized capaclty(ij, and that by is 4*r signature on the Instrument the person, or the entity upon behalf of which the person acted, executed the instrument. Witness my hand and � �official seal. Signature oC�GQJ�(.t 0• LSUE A. FuSAW Commtafarl N 1Z164]>; M01ory Public' Ca fonlio Cohan County 1@*CcffmB0wAp242l1131 MAIL. TAX STATEMENTS AS DIRECTED ABOVE Cr1.a�fin., 7/901 QnANT0=9) 11/20/02 16:17. BIDWELL TITLE 4 530 891 8753 NO.987 P003 lrsrfow No. 301277•SML Title Order No. 00301277 EXHIBIT ONE PARCEL ONE: Parcel 1, as shown on that certain Parcel Map, filed in the Office of the Recorder of the County of Butte, State of California, on July 30. 1973 in Book 46 of Maps, at Pagelsl 64, Excepting therefrom all hydrocarbons and minerals now or at any time hereafter situate and thereunder and which may be produced therefrom together with the free and unlimited right to mine, drill, bore, operate and remove from beneath the surface of said land at any level or levels 100 feet or more below the surface of said land for the purpose of development or removal of all hydrocarbons and minerals situated therein or thereunder or producible therefrom. PARCEL TWO: A right of way for road and public utility purposes over the Southerly 30 feet of parcel 2, as shown on that certain parcel map fled in the office of the'recorder of the County of Butte, state of California on July 30, 1973 in Book 45 Of maps at page 64. PARCEL THREE: A right of way for road and public utility purposes over a strip of land 30 feet in width tying Southerly and Easterly of and adjacent to the Southerly and Easterly line of Parcels 1 and 2 as shown on that certain parcel map filed in the office of the recorder of the County of Butte, State of California on July 30, 1973 in Book 46 of maps at page 64. NOTES RESIDENTIAL 058-720-039 02-3232 i� PERMIT NO. _ HEIL, DON & CAROL ' BIG BEND RD., OROVILLE CONT: EXECUTIVE HOMES + NEW MH PERM FND NEW SITE THE HCD FORM 433A FOR THIS MH CANNOT BE RECORDED UNTIL ONE OF THE FOLLOWING HAS BEEN TURNED IN TO THE BUILDING DIVISION: (1) LICENSE PLATE(S) OR DECAL (THE INSPECTOR MUST RETREIVE). (2) STATEMENT OF FACTS (ONLY ON NEW MH'S). INSPECTOR TO VERIFY SERIAL & LABEL #'S. r t 11 SPECIAL CONDITIONS 11 CHECKED ` BY SRA FLOOD CERTIFICATE REQ. FIRE SPRINKLERS REQ. SPECIAL INSPECTION ITEMS VERIFY USE PERMIT CONDITIONS SUB -STANDARD HOUSING LETTER OFFICE COPY k Address GAS Meter By L_LDat EL C M Y 2 JOB FINALED (Date)*!'XhxS Signature = OK = Not OK = NotReadyable MOBILE HOMES Date MOBILE HOME UTILITIES (Plans) OK except #'s 1. Zoning Requirements -Setbacks -Easements oils; Special MH Support Sketch ll; Sewer; Location -Test -Fall -C/O -Concrete 4. Water; Location -Test -Easement Needed (Sketch) 5.. Electricity; Location-Clearances-Grnd-/ /Amp -Concrete 6. Gas; Location-Tes -Wrap;-/ P' L -ft . / /'Nat. or /& P' L "ftf�4 P LPG b;e�eII Clearance & Disconnect If 8. Utility Clearance Date DECKS, COVERS, CARPORTS, GARAGES (Plans) OK except #'s Card B-1 Date Card B-1 Date Requirements -Setbacks -Easements Card B-1 Date Card B-1 Date MOBILE HOME INSTALLATION (Plans) OK except #'s 1. Zoning Requirements -Setbacks -Easements 2. Footings; Size -Spacing -Marriage Line 3. Gas; MH Test -Demand -Valve -Connector 4. Electricity; MH Test -Crossovers -Breakers -Clearances 5. Drain; MH Test -Fall -Flex Connector 6. Water; MH Test -Regulator -Connector 7. Water and Sewer Connected -C/O to Grade -HD Approval 8. Gas and Electricity Tagged Roof; Shthg-Roofing 9. Tie Downs -Type -Installation Cert. Ext.; Steps -Doors -Landings 10. Exits; Insp.-Sketch Braced Wall Panels 11. Cert. of Occupancy Date Card B-1 Date Card B-1 Date Date Date Card B-1 Date Card B-1 Date 1. Card B-1 Date Card B-1 Date PERMANENT END SYSTEM (ONLY) Line H Test -Demand -Valve I icity; MH Test ater; MH Test jeer and Sewer Connected License Decals Verify #'s with Office Date Card B-1 Date Card B-1 Dat Card�B-1 Date Card B-1 V� h -617 // , 3/3�� V r�•.c�-j-it��c- `tA 4alJs6r./� MISCELLANEOUS Date DECKS, COVERS, CARPORTS, GARAGES (Plans) OK except #'s 1.Zoning Requirements -Setbacks -Easements 2. Footings; Soils -Size -Depth -Spacing -Connectors -Steel 3. Decks, Girders and/or Joists -Decking -Bracing -Stairs -Rails 4. Wood Awn.; Posts- Beams-Rftrs-Connectors Shthg-Frg-Bracing 5. Alum. Awn.; Columns -Connections -Splice -Decal -Enclosures 6. Carports; Windows -Doors 7. Electric 8. Frmg.; Sills-Anchors-Studs-Rftrs-Trusses 9. Siding; Nailing -Veneer -Stucco -Mesh 10. Roof; Shthg-Roofing 11. Ext.; Steps -Doors -Landings 12. Braced Wall Panels Date Card B-1 Date Card B-1 Date Card B-1 Date Card B-1 Date POOLS (Plans) OK except #'s 1. Setbacks -Easements 2. Soils; Compaction -Structure Stability 3. Pool Structure; Steel -Connections -Thickness Dead Men -Lining 4. Elec.; Receptacles and Lighting, Distance-GFI 5. Elec.; Pool Lighting; 15 Volts-GFI 6. Elec.; Enclosures; Conduit Entries -Terminals -Listed 7. Elec.; Bonding; Metal w/5' -Circulating Equip. -Heater 8. Elec.; Grounding; Equip. w/5' Circulating Equip. -Pool Lghtg. Boxes -Enclosures -Panel boards -Ins. to Main Conduit 9. Health Department Approval 10. Plumb.; Cir. Test -Water Supply Test 11. Light Niche 12. Enclosure; Fencing -Alarms Date Card B-1 Date Card B-1 Date Card B-1 Date Card B-1 J=OK 0 = Not OK = Not Applicable . = Not Ready RESIDENTIAL (Single & Duplex) Date UNDERFLOOR (Plans) OK except #'s 1. Zoning -Setbacks -Easements -Flood -Slope 2. Ftg., Main; Soils-Elec. Grnd.-/ /" Ftg. Depth 3. Ftg., Garage; Soils-Steel-Elec. Grnd.-/ /" Ftg. Depth 4. Ftg., Porches & Decks; Soils -Steel-/ /" Ftg. Depth 5. Stemwalls, Main; Steel-Blockouts-Wrapped 6. Stemwalls, Garage; Steel-Blockouts-Wrapped 6a. Hold Downs and Special Anchors 7. Slab, Steel -Wrapped 8. Piers -Fireplace Ftg.-Steel 9. D.W.V.; Fall -Fitting -Test -2 Way C/O -Sewer Test 10. UF, Gas Pipe; Size Anchors -Yard Gas Piping; Size Test 11. Water Pipe: Test -Anchors -Regulator -Service Test Date 12. Electric Underground 13. Plenums & Ducts; Clearance -Material -Support -Ins. 14. Girders -Sills -Anchor Bolts-Joists-Vents-Crippies 15. Access & Ventilation 16. Insulation 51. Bdrm. Windows or Exiting Doors -Sill Ht. & Dimensions Date Card B-1 Date Card B-1 Date Card B-1 Date Card B-1 Date PLUMBING (Permit) OK except #'s 17. Water Htr.; Vent -Access -Combustion Air Baffle 18. Water Pipe; Test & Anchor -Nail Protection 19. D.W.V.; Test Fittings & Anchor -Nail Protection 20. Shower Pan; Test, First Floor -Tub Access 21. Test Tub & Shower, Second Floor -Tub Access 22. Gas Pipe; Sixe & Anchors 23. Fire Sprinkler; Test 62. Insulation -Walls -Ceilings Date Card B-1 Date Card B-1 Date Card B-1 Date Card B-1 Date ELECTRICAL (Permit) OK except #'s Date 24. Fixture & Transformer Clearance -Ins. Protection 25. Elec. Receptacles Spacing -Lights & Switches at Doors 26. Size Boxes & No. of Conductors Stapled 27. Romex Installed Close to Edge of Studs & C.J. 28. Equip. Ground made up w/Mech Fasteners -Bond Gas & Water 29. 2 Appliance Circuits in Kitchen & Conductor Size GFI 30. Subfeed Wire Size/ /ga. Cu or AI-A.C. Wire Size/ /ga Cu or Al 31. Range Circle/ /ga Cu or AI -Oven Circ. / /ga Cu or Al Insulated Neutral 0 Yes 0 No 32. Service -Riser Conductors & Ground Main Disconnect 33. Equip. Clearances Panels-Motors-Mech. Equip. 34. Clothes Closet Light -Shower Light -Spa Light 35. Smoke Detector 75. Garage Fire Door; Swing -Landing -Closure Date Card B-1 Date Card B-1 Date Card B-1 Date Card B-1 Date MECHANICAL (Permit) OK except #'s 36. A.C. Ducts Insulation & Support 37. Vent Fan, Exhaust above insulation 38. Condensate Drain & Overflow, Size & Grade 39. Furnace -Vent Access -Comb. Ait-Return Air Vent 115 Outlet 40. Attic Access & Platform if Furnace in Attic Date Card B-1 Date Card B-1 Date Card B-1 Date Card B-1 Date FRAMING (Permit) OK except #'s 41. Sills Proper Materials & Anchors 42. Walls Studs -Nailing Spacing & Braces -Plates -Sound 43. Bearing Walls over Girders & Floor Nailing 44. Draft Stop in Walls (rat proof) 45. Fire Stops, Furred Ceilings -Stairs -Chasers -Tubs 46. Headers & Beams -Size & Bearing Date FRAMING (Continued) 47. Hangers -Post Caps -Anchors -Connectors 48. Cling. Joist-Rftr. Ties-Purlin-Roll Brac.-Truss-Shting.-Rtng. 49. Fireplace Ties or Type A Flue -Fireplace Throat Clearance 50. Attic Access; Size & Romex Protection -Draft Stop -Ins. Baffles 51. Bdrm. Windows or Exiting Doors -Sill Ht. & Dimensions 52. Garage Fire Protection Framing -RC Channel 53. Property Line Firewall & Openings 54. Ext. Doors -One 3' -Check Garage 3rd Story, 2 Exits 55. Stairs; Width -Headroom -Rise -Run -Landing -Fire Protection 56. Plywood on Roof Overhang -Attic Vents -Rafter Outriggers 57. Siding -Nailing Veneer 58. Stucco Mesh -Drip Screed -Fd. Vents-Underflr. Access 59. Glazing Area -Glass Protection -Skylights -Plastic 60. Shear Walls; Nailing -Bolts 61. Brace Interior/Exterior Wall Panels 62. Insulation -Walls -Ceilings 63. I nfi Itration-Walls-Windows Date Card B-1 Date Card B-1 Date Card B-1 Date Card B-1 Date FINAL (Plans) OK except #'s 64. Ext. Steps -Door & Sidelight Protection -Landings 65. Smoke Detector 66. Furnace Vents -clearance -Comb, Air -Connector - In Garage; Above Floor-Ducts-Mech. Protection 67. Bedroom Exiting 68. G.F.I. & Bath Fixtures & Tub Access -Spa 69. Elec. Trim & Subpanel, Breaker Sizes & Labels 70. Stairs & Rails 71. Fireplace or Stove, Clearance -Hearth 72. Elec. Outlets at Wood Panel, Int. & Ext. 73. Kit. Fixt. & Appliance; Ground -Air -Gap -Cooking Clearance 74. Elec. Outlets & Receptacles at Kit. Counter 75. Garage Fire Door; Swing -Landing -Closure 76. A.C. Duct in Garage -Damper 77. Wtr. Htr.; Vents -Clearance -Comb. Air Connector-P.R.V. in Garage; Above Floor-Mech. Protection 78. Plb.; Elec. & Mech. Equip. Listed for Location 79. Elec. Receptacles in Garage (F.F.I.)-Romex Protection 80. Insulation -Foam -Looked in Attic 81. Guard Rails & Deck Construction -Post Caps 82. Fdn. VBents & Crawl Hole Door Drainage & Wood -Earth Clearance Looked under Floor ❑ Yes _ 83. Following Instld./Drive 0 Yes O No/Walks D Yes O No/Planters 0 Yes O No 84. Stucco Brown -Finish 85. A.C. Unit Disconnect, Electrical -Plumbing 86. Vents Above Roof, Plbg-Appliance-Fireplace-Clearance to Openings 87. Water Well, Disconnect, Electrical, Plumbing 88. Exterior Elec. Trim, G.F.I. Receptacle -Underground 89. Ventilation Throughout House 90. Glass Protection 91. Corrections from Previous Inspections 92. Gas Test -Meters Tagged, Gas -Electric 93. Water & Sewer Connected -C/O to Grade -HD Approval 94. Energy Compliance Certificate -Other Certificates 95. Address Posted 96. Fire Sprinkler Date Card B-1 Date Card B-1 Date Card B-1 Date Card B-1 Date Card B-1 Date Card B-1 Comments at Final: COUNTY OF BUTTE BUILDING DIVISION DEPARTMENT OF DEVELOPMENT SERVICES 411 Main Street - Chico, CA - (530) 891-2751 7 County Center Drive - Oroville, CA - (530) 538-7541 CORRECTION NOTICE ER PERMIT NO. A routine inspection indicates that the following violations of butte county Ordinances exist at the above address and should be corrected. Please notice this office when correction of work is completed. If you have any questions pertaining to this matter, or need additional explanation, please contact this office immediately. Date ��/ 6� Inspector i4�✓✓® REV 10/92 COUNTY OF BUTTE - DEPARTMENT OF DEVELOPMENT SERVICES - BUILDING DIVISION 7 County Center Drive • Oroville, California 95,965 • Telephone (530) 538-7541O Z E7U (Rev.12/96) APPLICATION AND PERMIT '•�"'+ ASSESSOR PARCEL NUMBER ZONING r% BUILDING PERMIT OWNER T`" TELEPHONE IV,�05 SO. FT. OCC. BUILDING VALUATION R 64,260. OU OWNERS MAIUNG DRESS 9 F CT i.o )i T t "• CONTRACTORS NAME "� TELEPHONE O 7 CONTRACTORS MAILING ADDRESS F(zP t1FCM110DI r• -705973 y CONSTRUCTION LENDER Fireplace LENDER'S MAILING ADDRESS Total Valuation $54.260. ARCHITECT OR ENGINEER LICENSE No. Flin Fee $ 20.00 Permit Fee 48 $ 241, W ARCHITECT OR ENGINEERS MAILING ADDRESS Plan Checking Fee $ 21. 00 BUILDING ADDRESS BIG RM RD QW111i 17 Energy Plan Checking Fee $ $ PERMIT FEE S R4 LAT NO. SUBDIVISION'S NAME PARCEL MAP PLUMBING PERMIT Fling Fee 20.00 Each Trap 7.00 USEOFSTRUCTURE SF ❑ Duplex ❑ Mobilehome ❑ Other SPECIFY Solar or heat pump water heater 23.00 Water piping 015.00 Each gas water heater or vent 15.00 TYPE OF WORK ''New ❑ Addition ❑ Remodel ❑ Utilities ❑ Installation ❑ Other ❑ Describe . Work: NEW IH PERM EM NEW SITE Gas piping system 1 - 5 outlets 15.00 1 S Building sewer 1 5.00 'S Mobile Home S G W @20.00 PERMIT FEE $ 65.00 ELECTRICAL PERMIT I Fling Feel 20.00 000V OR LESS Main Service 20..OR LESS 23.00 13.00 LICENSED CONTRACTOR'S DECLARATION I hereby affirm under penalty of perjury that I am licensed under provisions of Chapter 9 (commencing with Section 7000) of Division 3 of the Business and Professions Code, and my license is in -full force and w effect License Class '4tLio. DECLARATION I hereby affirm under penalty of perjury that I am exempt from the Contractors License Law for the following reason: L ❑ I, as owner of the property, or my employees with wages as their sole compensation, will do the work, and the structure is not intended or offered for sale. ❑ I, as owner of the property, am exclusively contracting with licensed contractors to construct the project. ❑ 1 am exempt under Sec. Business and Professions Code for this reason . WORKERS' COMPENSATION DECLARATION 1 hereby affirm under penalty of perjury one of the following declarations: ❑ 1 have and will maintain a certificate of consent to self -insure for workers' compensation, as provided for by section 3700 of the Labor Code, for the performance of the work for which this permit is issued. 1110-fhave and will maintain workers' compensation insurance, as required by Section 3700 of the Labor Code, for the performance of work for which this permit is issued. My workers',compensation insuvance carrier an, policy number are: Carrier Zy/P F AII;, �u Al L3 Main Service zoo. TO L000A 46.00 NEW CONST. DW EWNG UP. SO OR ADDNS. ( a ACC. stns. 3.5QFT; N..IC ,D MULTI-OUTIETunS @7.50 WER APPARATUS aPINGLE OUTLET CIR. Ex. Occup. OUTLET OR FIXTURES BAL0 +:50OWNER-BUILDER Ex. Occup. oUTLssrs RE D.oE A 5.00 Temporary Service 23.00 Mobile Home Facilities 20.00 Misc. Wiring 23.00 23.00 PERMIT FEE $66.00 MECHANICAL PERMIT Fling Fee 20.00 Heating Cooling Hood 6.50 Ventilation PERMIT FEE $ Policy Number //-a C- 't -7 - 0-,)tr (The above sections need not be b-ompleted if the permit is for work of a valuation of one hundred dollars ($100) or less.) ❑ 1 certify that in the performance of the work for which this permit is issued, I shall not employ any person in any manner so as to become subject to workers' compensation laws of California, and agree that if I should become subject to the workers' compensation provisions of section 3700 of the Labor Code, I shall forthwith)comply with those provisions. X_ i-vL- . _ Date �/ — (i/ Q iT Signature of Applicant - ❑ Owner ❑ Contractor EI Agent An OSHA permit is required for excavations over 60" deep and demolition or construction of structures over 3 stories in height. Mobile Home Installation Fee $ Energy Inspection Fee $ occ CONST. TYPE TOTAL FEE $ 415.00 HA2. ...•- p. FE IMP FLOOD CDF PARCEL pD/ yr HD §SUE This permit is hereby issued under the applicable provisions of the Butte County Code and/or Resolutions to do work indicated above for which fees have been paid. �f 1 By t. •1 / n Date ;.W11 0 PERMIT EXPIRES ON Z / I' 014- ` to Receipt No. 364439 t83-00// 5 ti WHITE-D.D.S.-B.D. CANARY -ASSESSOR PINK -INSPECTOR GOLDENROD -APPLICANT FLEETWOOD HOMES OF CALIFORNIA, INC. 18 N. PIONEER AVE. PO BOX 1308 WOODLAND, CA. 95776 MC# 17 Date of Manufacture HUD label No.(s) / PFS795896 Floors........................................................................ PFS795897 v Manufacturer's Serial Number(s) and Model Unit Designation WOODLAND PARK 4453A Air ducts in ceiling......................................................... CAFL217A26214-WP13 Air ducts installed outside the home ................................. CAFL217B26214-WP13 The following are the duct areas in this home: Design Approval by (D.A.P.I.A.) PFS CORP. This manufactured home Is designed to comply with the federal manufactured home construction and safety standards in force at time of manufacture. (For additional information, consult owner's manual.) The factory installed equipment includes: 56 .5 sq. ft. Equipment Manufacturer Model Designation For Heating COLEMAN DGAT056 For Cooking WHIRLPOOL SF3020 Refrigerator WHIRLPOOL ET8CH Water Heater RHEEM 21I40T Smoke Detector KIDDE 1275E Dishwasher WHIRLPOOL DU890S Fireplace MARCO BM36 HOME CONSTRUCTED FOR X ZONE I . ZONE II ZONE III EXP. "D" This home has not been designed for the higher wind pressure and anchoring provisions required for oceantcoastal areas and should not be located within 1500' of the coastline in Wind Zones II and III, unless the home and its anchoring and foundation system have been designed for the increased requirements specified for Exposure D in ANSI/ASCE 7 - 88. This home has ( ) has not (X) been equipped with storm shutters or other protective coverings for windows and exterior door openings. For homes designed to be located in Wind Zones II and III, which have not been provided with shutters or equivalent covering devices, it is strongly recommended that the home be made ready to be equipped with these devices in accordance with the method recommended in manufacturers printed instructions. Design roof load zone map: NORTH North 40 psf X South 20 psf X Middle 30 psf _ Other psf COMFORT HEATING This manufactured home has been thermally insulated to conform with the requirements of the federal manufactured home construction and safety standards for all locations within Uo value Zone 1,2,3 . (See map at bottom) Heating equipment manufacturer and model (See list at left). The listed heating equipment has the capacity to maintain an average 70 degrees Fahrenheit temperature in this home at outdoor temperatures of — 10 4degrees Fahrenheit To maximize furnace operating economy, and to conserve energy, it is recommended that this home be installed where the outdoor winter design temperature (97 f%) is not higher than —51 degrees Fahrenheit. The above information has been calculated assuming a maximum wind velocity of 15 mph at standard atmospheric pressure. COMFORT COOLING Air conditioner provided at factory (Alternate 1) Air conditioner manufacturer and model (see list at left). Certified capacity B.T.U./hour in accordance with the appropriate air conditioning and refrigeration institute standards. The central air conditioning system provided in this home has been sized assuring an orientation of the front (hitch end) of the home facing . On this basis the system is designed to Maintain an indoor temperature of 75°F when outdoor temperatures are °F dry bulb and °F wet bulb. The temperature to which this home can be cooled will change depending upon the amount of exposure of the windows of this home to the sun's radiant heat. Therefore, the home's heat gains will vary dependent upon its orientation to the sun and any permanent shading provided. Information concerning the calculation of cooling loads at various locations, window exposures and shadings are provided in Chapter 22 of the 1989 edition of the ASHRAE Handbook of Fundamentals. Information necessary to calculate cooling loads at various locations and orientations is provided in the special comfort cooling information provided with this home. Air conditioner not provided at factory (Alternate 11) The air distribution system of this home is suitable for the installation of central air conditioning. The supply air distribution system installed in this home is sized for a manufactured home central air conditioning system of up to 6 3 , 0 0 0 B.T.U. /hr. rated capacity which are certified in accordance with the appropriate air conditioning and refrigeration institute standards, when the air circulators of such air conditioners are rated at 0.3 inch water column static pressure or greater for the cooling air delivered to the manufactured home supply air duct system. Information necessary to calculate cooling loads at various locations and orientations is provided in the special comfort cooling information provided with this manufactured home. To determine the required capacity of equipment to cool a home efficiently and economically, a cooling load (heat gain) calculation is required. The cooling load is dependent on the orientation, location and the structure of the home. Central air conditioners operate most efficiently and provide the greatest comfort when their capacity closely approximates the calculated cooling load. Each home's air conditioner should be sized in accordance with Chapter 22 of the American Society of Heating, Refrigerating and Air Conditioning Engineers (ASHRAE) Handbook of Fundamentals 1989 edition, once the location and orientation are known. INFORMATION PROVIDED BY THE MANUFACTURER NECESSARY TO CALCULATE SENSIBLE HEAT GAIN Walls (without windows and doors) .................................... °U° .06 Ceiling and roofs of light color ......................................... °U° .03 Ceilings and roofs of dark color ....................................... °U° .03 Floors........................................................................ °U° .05 Air ducts in floor........................................................... 'U' .05 Air ducts in ceiling......................................................... °U° NA Air ducts installed outside the home ................................. °U' .25 The following are the duct areas in this home: Air ducts in floor........................................................... 71 sq. 0. Air ducts in ceiling.......................................................... NA sq. ft. Air duds outside the home ............................................... 56 .5 sq. ft. U/O VALUE ZONE MAP WA NH MT ND VT ME OR MN ID SD WI WY MI NY MA NV NE IA IL IN OH RI PA CT NJ CA UT CO KS Mo VA DE AZNM.._OK`,. .. TH AR No SC ZONES U -VALUES LA MS AL GA 1 0 0.116 L AK # TX 2 a o ... FL ® 0.096 HI 3 0 0.079 .. � ., �• - { _ _ .; i i �"- � �. . .,- ' �� , . � � � r _ .. '� � . .. c � .. COUNTY OF BUTTE - DEPARTMENT OF DEVELOPMENT SERVICES - BUILDING DIVISION r� 7 County Center Drive • Oroville, California 95965 • Telephone (530) 538-7541 o Z (Rev. 12/96) APPLICATION AND PERMIT -�M >z_ ASSESSOR PARCEL NUMBER ZONING BUILDING PERMIT OWNER SO. FT. BUILDING VALUATION jO�CC. 0 L` 64 260.00 OWNER'S MAIUNG DRESS CONTRACTOR'S NAME 7 TELEPHONE Fyprl TrTJJE HOMES 1891-60192 CONTRACTOR'S MAILING ADDRESS 3042 ESPIANADEQ141GQGA 95973 CONSTRUCTION LENDER 5 9 Fireplace LENDER'S MAILING ADDRESS Total Valuation $' ARCHITECT OR ENGINEER LICENSE NO. Filen Fee $ 20.00 Permit Fee 482Z2 $241.00 ARCHITECT OR ENGINEERS MAILING ADDRESS Plan Checking Fee $ BUILDINGADDRESS BIC, BEND RD GRAQVILL-E Energy Plan Checking Fee $ $ PERMIT FEE $ 281, LAT NO. SUBDIVISIONS NAME PARCEL MAP PLUMBING PERMIT Filing Fee 20.00 Each Trap 7.0023.00 USEOFSTRUCTURE SF ❑ Duplex ❑ Mobilehome ❑ Other SPECIFY Solar or hest um water heater Water piping 15.00 00 .15 Each gas water heater or vent 15.00 TYPE OF WORK New ❑ Addition ❑ Remodel ❑ Utilities ❑ Installation ❑ Other ❑ Describe Work: NEW MH PERM FM NEW SITE Gas piping system 1 - 5 outlets 15.00 Building sewer 15.00 Mobile Home I S I G I W 920.00 ' PERMIT FEE $ 65.00 ELECTRICAL PERMIT Filing Fee 20.00 800R UE Main Service 20pA OR LESS 23.00 00 LICENSED CONTRACTOR'S DECLARATION I hereby affirm under penalty of perjury that I am licensed under provisions of Chapter 9 (commencing with Section 7000) of Division 3 of the Business and Professions Code, and my license is I Ofull forC a d effect. License Class Lic. No. �„ OWNER -BUILDER DECLARATION I hereby affirm under penalty of perjury that I am exempt from the Contractors License Law for the following reason: ❑ I, as owner of the property, or my employees with wages as their sole compensation, will do the work, and the structure is not intended or offered for sale. ❑ I, as owner of the property, am exclusively contracting with licensed contractors to construct the project. ❑ 1 am exempt under Sec. Business and Professions Code for this reason Main Service Zoog To L000A 46.00 NEW CONST. DWELLING OCCUP. SO OR ADDNS. ( a ACC. S.3.5¢FT. NEW RESID. MULTI -OUTLET 97,50 POWER APPARATUS a SINGLE OUTLET CIR. 20 Q 1.00 E x. Occup. CUTLET OR FocruREs BAL p .so FIAPPLNS. OR S.00 Ex. Occup. ounFrs RESID. EA Temporary Service 23.00 Mobile Home Facilities 20.00 Misc. Wiring 23.00 PERMIT FEE $66.00 WORKERS' COMPENSATION DECLARATION 1 hereby affirm under penalty of perjury one of the following declarations: ❑ 1 have and will maintain a certificate of consent to self -insure for workers' compensation, as provided for by section 3700 of the Labor Code, for the poormance of the work for which this permit is issued. grl have and will maintain workers' compensation insurance, as required by Section 3700 of the Labor Code, for the performance of work for which this permit is issued. My worker ' corn ensation in1LvA=e carrier an policnumber are: Carrier f &--Al U MECHANICAL PERMIT Filing Fee 20.00 Heating Cooling Hood 6.50 Ventilation PERMIT FEE $ Policy Number cli (The above sections nee8 not b1b d-orril5leted Me permit Is for work of a valuation of one hundred dollars ($100) or less.) ❑ 1 certify that in the performance of the work for which this permit is issued, I shall not employ any person in any manner so as to become subject to workers' compensation laws of California, and agree that if I should become subject to the workers' compensation provisions of section 3700 of the Labor Code, I shall' forthw' comply with th se provisions. X Date ZZ__ 6? Signa ure of Applicant - ❑ Owner ❑ Contractor BItge-nt An OSHA permit is required for excavations over 60" deep and demolition or construction of structures over 3 stories in height. Mobile Home Installation Fee $ Energy Inspection Fee $ occ CONST. TYPE TOTAL FEE $ 415.00 HAZ. D. FE IMP D CDF PARC V PD HD SUE This permit is hereby issued under the applicable provisions of the Butte County Code and/or Resolutions to do work indicated above for which fees have been paid. eo Byt I Date/ i 3 PERMIT EXPIRES ON �W11 Date rReceiptNo.. TE•D.D.S-B.D. CA A S OR PINK -INSPECTOR GOLDENROD -APPLICANT TO: Building Department FROM: Environmental Health SUBJECT: Sani ation Clearance Me -1 ,. - N\a Owner Location a Plan Approved for: Sewage Dispossal-,_Water Suppt Pu! t Z Clearance for dwelling. Other ? D 1J-7'1 l/ `v Hold final for: Final clearance O.K. for: NOTE: h )-A (� t , PII_� Environmental Health Specialist 8/96 64o2 Plan d Roos Stan I Sana to 6.0 Priv I � I I Da COUNTY OF BUTTE -DEPARTMENT OF DEVELOPMENT SERVICES -BUILDING DIVISION 7 County Center Drive, Oroville, CA 95965 Phone (530)538-7541 Fax (530)538-2140 + PERMIT APPLICATION�DATA SHEET 1 OWNER: tSSWO'PARCELNUMBER7VD Proposed Building Use ( jnter Technician: Date: / Item required in order to apply for a pe mit. All boxes MUST be checked OR marked NA in order to apply. Vlot plans, 3 or 4 sets, signed,ity the preparer of the plans. Complete plans, 3 or 4 sets, signed by the preparer of the plans. Engineered plans, 3 or 4 sets, with wet signature on plans AND 2 sets of stamped and signed calculations. 4. Engineered truss details and layouts in duplicate. No faxes! ❑ 5. Energy compliance dNkiqata d supporting documentation in duplica �. Manufactured home sheets and installation instructions arriage line information,�E) Floor Plan, (D) Tie down or foundation plans, all ih"dunlicate. ❑ 7. Metal buildings: (A) Metal Building Plans, (B) Foundation plans and calculations in triplicate, (C) Elevation views in triplicate. (D) Floor plans in triplicate. All of these must be stamped and wet -signed by the engineer. Items required for initial plan review. If checked items have not been received, plan review cannot proceed. The.permit will be indexed and returned to the plan review line-up when required items are received. Date Received By ❑ 8. Flood Elevation Certificate, wet -stamped and signed, in duplicate ................................ ❑ 9. Plot plan and business license approval from the City of Biggs .................................... ❑ 10. Letter of intent for non-residential buildings......................................................:.. ❑ 11. Detached Accessory Building Form filled out by the owner ..................................... ❑ 12. Hazardous Material Form............................................................................... _ ❑ 13. Other Re arcing items needed to issue the permit. (May require additional plan review upon receipt of the following items.) 4. ees as shown on the attached Schedule of Fees Due Sheet ...................................... 15. Statement of Intent for Non -heated and A/C Buildings ....................................... -Sanitation and plot plan approval from the Environme tal Health Dja rtment in❑ 17.17. CCiity of Chico Plumbing permit ........................... .............. ............... ��1�°—� a i .lifornia Department of Forestry plan approval �paid. Sentb . .................... ❑ 19. Planning approval for (A) Use: p 1G (B)Parking: (C) Pa el Check: ❑ 0. Contact Land Development about ❑ Improvements, ❑ Drainage ............................... � 21. Encroachment Permit for driveway from the Public Works Dept. (construction approval prior to occupancy). 2. Pre -Inspection for required ................ Contractor's license information. (Number, Name Style, Classification) ...................... 24. Worker's Compensation Carrier and Policy Number ..............:.............................. ❑ 25.; Owner -Builder Verification (❑ Given to owner, ❑ Mailed to owner) ..................... [71.026. Letter of Signature authorization.................................................................... 27 Recorded copy of Agricultural Acknowledgment Statement .................................... 8. ManufacturedDome utility clearance .................................................... ......... ❑ 29. BMtiiA violations andkr expired permits ............................................. ... K' ❑ 30. ran ee H. Title/Statement of Facts, ❑ Letter from Legal Owner, eck to H.C.D. Other: e-.7 — When issued Telephone 7 and hold for pickup. 1/Y0 3 ob I have been informed the above)/,tems and requirements for obtaining a building permit. Applicant: Date:. -- 1. Index permit application for the i be ed: ,wia Plan Check Letter 2COW Ir 9W 'onal items required Contract ,designer, owner, was vis a ove data by &onWi �1, ❑ counter, by ,Date: 2 kql acto designer, owner, was advised of the abo e d a by holrw,8.0 il, ❑ counter, by 12-3 Date:ans reviewed by: ✓� Date: D Plans appro ed by: �dg Date: Structural reviewed by: Date: I Structural approved by: Date: Note transfer by: Date: l'oN�roC/o/ �0%fD.vc //2110 3 2 /� Yellow: Buildine Division , COUNTY OF BUTTE DEPARTMENT OF DEVELOPMENT SERVICES - BUILDING DIVISION 7 COUNTY CENTER DRIVE - OROVILLE, CALIFORNIA 95965 - TELEPHONE (530) 538-7541 SCHEDULE O FEES DUE G % �jC OWNER A.P. # N�O I W�V J PROPOSED BUILDING USE DATE V �Z J RECEIPT # DATE REC. 1. BUILDING PERMIT FEES $ �,6c� I/� �� �� Balance Due ...................... �j' ., Additional Fees Due ................. $ Additional Fees Due ................. $ Revised Plan Checking Fee ... . 2. SCHO DISTRICT FEES U (paid a s , ffi e) ( ab f C /I/ 3. SHEREW FEES (paid at Building Division) � apo f � jc�/ Residential ...................... x $360.00 = $ s� J/t'il'JcS / Ire Units Commercial (sq. ft:) ............... x $0.03 = $ Sq. ft. 4. URBAN AREA FEES (paid at Building Division) t Residential ................... x = $ # Units Amt. Commercial (sq. ft.) ............ -x-=$ Sq. ft. Amt. 5. RECREATIONAL DISTRICT FEES (paid at District Office) (Available after Plan Check) 6. THERMALITO DRAINAGE DISTRICT FEES 4 $510.00 (paid at Building Division) (//� 7 SRA FIRE INSPECTION AND PLAN CHECK $89.00 (paid at Building Division) 8. WATER TENDER FEES (Battalion # ) $200.00 (paid at Building Division) 9. CSA 87 TRAFFIC FEE $2500.00 (paid at Building Division) 10. OTHER At time of permit application, I was advised the above fees are required to be paid prior to issuance of the building permit. These fees may be changed during the plan checking process. APPLICANT DATE Pursuant to Government Code Section 66020, you are hereby notified that items 2, 3, 4, 5, 6, 7, 8, 9, and 10 above may have been imposed on your project. You have 90 days from the date of approval of the project or from the imposition of the above mentioned items during which you may protest. The requirements for a protest are specified in Government Code Section 66020(a). Original - Buiding Div. 2nd Copy - Applicant - 3rd Copy - Owner ' (Rev. 6/00) COUNTY OF BUTTE - DEPARTMENT OF DEVELOPMENT SERVICES - BUILDING DIVISION 7 County Center Drive - Oroville, California 95965 - Telephone (530) 538-7541 PERMI N 3ev.;2/96) APPLICATION AND PERMIT - ��- �Z ASSESSOR PARCEL NUMBER .t ^ _ ZO'-NO � J BUILDING PERMIT ibimatoj,jm MAIUNG ADOWS _ ,% a JJW CONSTRUCTION LEND ER LENDER'S MAILING ADDRESS ARCHITECT OR ENGINEER ---------- MCMTECT OR ENGINEERS MAIUNG ADDRESS ..- SUILDINGADDRESS ._/1 • ll LOT NO. .� I SUBDIVISIONS NAAIEfy_ H -6 S -L-) - -- PARCEL MAP USEOFSTRUCTURE SF ❑ Duplex ❑ MobilehomeX Other sPEcsY TYPE OF WORK New*- Addition O Remodel ❑ Utilities ❑ Instanation O Other O FJ - Sid -2-f) '4�crm:} �76►�d � � sSRA v.� O*htX' AwowAYuc;red Total Valuation is PERMIT FEE $ �— Flinn Fee E 20.00 Permit Fee S Main Service Plan Checking Fee S NEW CONST: OR AODNS. Energy Plan Checking Fee $ N0ILRESID. MULTNOUTI.ET At1cm c Rcurrs 1 S PERMIT FEE S PLUMBING PERMIT Fling Fee 20.00 Each Trap 7.00 Solar or heatpump water heater 23.00 Water piping 15.00 Each gas water heater or vent 15.00 - 5.00 -.Gas Gas I in stem 1 - 5 outlets 15.00 �- Building sewer 15.00 Mobile Home I S G W @20.00 EX. Occup. PERMIT FEE $ �— ELECTRICAL PERMIT Fling Feel 20.00 M Main Service "OV OR LES: ao. oR LEss 23.00 Main Service 200A TO 1000A 46.00 NEW CONST: OR AODNS. DWELLING DOCVP i ACC. BLD:. SO N0ILRESID. MULTNOUTI.ET At1cm c Rcurrs 1 1 97.50 EX. Occup. OVTtEr OR nXTVRES 20 G' 1'00 BAL ® .90 1 Ex. Occup. FIXED APPLNS. OR OVnETS RESID. EA 5.00 Tem2orary Service 23.00 Mobile Home Facilities 20.00 Misc. Wiring 23.00 PERMIT FEE S MECHANICAL PERMIT Fling Fee 20.00 Heating Cooling Hood 1 6.501 PERMIT FEt S Mobile Home Installation Fee $ Energy Inspection Fee $ OCC CONST. TYPE OT L EES "Az O ;DV- ND�'6;U This permit Is hereby Issued under the applicable provisions of the Butte County Code and/or Resolutions to do work Indicated above for which fees have been paid. By Date _ PERMIT EXPIRES ON AND WHEN RECORDED MAIL TO: BUTTE COUNTY BUILDING DIVISION 7 COUNTY CENTER DRIVE OROVILLE, CA 95965 IIII"III"IIIIIIII�II'III'I�I�I�I 2003-1000 1 1 9 1 Recorded Official Records CoBBUUTT Of TE CANDACE J. GRUBBS Recorder ROSEMARY DICKSON Assistant 01:49PM 07 -Jan -2003 REC FEE 7.00 CONFORM 1.00 Myles Page i of 1 AGRICULTURAL STATEMENT OF ACKNOWLEDGMENT FOR RESIDENTIAL DEVELOPMENT Section 26-8 of the Butte County Code required this acknowledgment to be recorded prior to issuance of a building permit. The property described herein is adjacent to land or included within an area zoned for agricultural purposes, and residents of this property may be subject to inconveniences or discomfort from the use of agricultural chemicals, including, but not limited to herbicides, pesticides, and fertilizers; and from the pursuit of agricultural operations including, but not limited to cultivation, plowing, spraying, pruning, and harvesting which occasionally generate dust, smoke, noise, and odor. Butte County has established agricultural purposes and residents within said zones and on adjacent property should be prepared to accept such inconvenience or discomfort from normal, necessary farm operations. All that real property situate in the County of Butte, State of California, described as follows: Parcel 1, as shown on that certain Parcel Map, $led in the Office of the Recorder of the County of Butte, State of California, on July 30, 1973 in Book 46 of Maps, at Page(s) 64. Date / ' 3 6 3 PROPERTY OWNERS: J State of Ca ifornia ) County of ) On An before me, personally appeared 9,. ('_a,rOj „�®� e— personally known to me (or proved to me on the basis of satisfact ry evidence) to be the person(s) whose name(s) is/are subscribed to the within instrument and acknowledged to me that he/she/they executed the same in his/her/their authorized capacity(ies), and that by his/her/their signature(s) on the instrument, the person(s) or the entity upon behalf of which the person(s) acted, executed the instrument. WITNESS my hand and official seal. Signature C� Seal: M,.:-CCOMM' 1 1335942 ' (rNOTARY PUBLCCMJ A.P. t 'COUNTY OF BUTTE" Comm EXPlras On. 22, 2005 a BUTTE'COUNTY SCHOOLS IMPACT FEE CERTIFICATION'FORM (One form per Building) School District Building IDepartment No. A.P. Number D / ' Jurisdiction, City r I \� ICounty Property Owner Property Location/Address tlX d lQd 61k, 4 Subdivision Residential Development _F7 ., No of Living MobilefHbme Units Installation17-~ Commer ial/Industrial ^New Addition Department Representative Lot No. to - C)vo , ................................................................................................................ _ �,• Sq. Footage / Addition/ •Supplemental -to (Group R) Conversion Permit # '(No foundation inspection); ................................................................................................................... Plans reviewedlby School District Sq. Footage (Including Exterior / R • ofed Areas) Date District Identification No. " 'QO `# — ` "u School District certifies that Q:V { C>,r_?::)ae I J (Applicant) t rri s ( An 0 (Street Address) .� (Phone Number) - anvdte., 6A 4qoqe7i;�; (City) - (State) (Zip Code) has complied with the requirements of Resolution No. ,�f _q0 by payment of $ ZQ �, . representing I OTC) square feet. AB 2926 $ FULL MITIGATION $ '' School District Representative Date Paid bv_Check # Remarks: Notice: You may protest the imposition of the fees identified above by submitting a written protest to the District, in compliance with Government Code Section 66020(a), within 90 days from the date fees are paid. Failure to submit a timely written protest will prohibit you from challenging the imposition of the fees in any court action. If, subsequent to the School District Representative signing this Butte County Schools Impact Fee Certification Form, the School District is notified by the applicable Local Planning Agency that this project is being reviewed under the California Environmental Quality Act (CEQA), this project may be subject to additional school fees to fully mitigate its impact on the school district's schools. White (applicant), Yellow (building department), Pink (school district) feeform.xls 00/98)dmm j.I AND WHEN RECORDED MAIL TO: BUTTE COUNTY BUILDING DIVISION 7 COUNTY CENTER DRIVE OROVILLE, CA 95965 COPY of Document Recorded 07 -Jan -2003 2003-0001191 Has not been compared with original BUTTE COUNTY RECORDER AGRICULTURAL STATEMENT OF ACKNOWLEDGMENT FOR RESIDENTIAL DEVELOPMENT Section 26-8 of the Butte County Code required this acknowledgment to be recorded prior to issuance of a building permit. The property described herein is adjacent to land or included within an area zoned for agricultural purposes, and residents of this property may be subject to inconveniences or discomfort from the use of agricultural chemicals, including, but not limited to herbicides, pesticides, and fertilizers; and from the pursuit of agricultural operations including, but not limited to cultivation, plowing, spraying, pruning, and harvesting which Occasionally generate dust, smoke, noise, and odor. Butte County has established agricultural purposes and residents within said zones and on adjacent property should be prepared to accept such inconvenience or discomfort from normal, necessary farm operations. j All that real property situate in the County of Butte, State of California, described as follows: I Parcel 1, as shown on that certain Parcel Map, filed in the Office of the Recorder of the County of Butte, State of California, on July 30, 1973 in Book 46 of Maps, at Page(s) 64. Date / ' 3 6 3 PROPERTY OWNERS: dakw- et State of Ca ifornia County of On ?-I before me, personally appeared 'arp 1 pip leo�:_ personally known to me (or proved to me on the basis of satisfactory evidence) to be the person(s) whose name(s) is/are subscribed to the within instrument and acknowledged to me that he/she/they executed the same in his/her/their authorized capacity(ies), and that by his/her/their signature(s) on the.instrument, the person(s) or the entity upon behalf of which the person(s) acted, executed the instrument. WITNESS my hand and official seal. SignatureD, �a Seal: ^` CYNTHIA JOHNSON COMM., 11335942 A.P. #_OS'P-;U0 - 03 % In W.UNTY NOTMY PHUC-MFORNA COOF BUTTE COMM Expires Dss. 22, 2005 tjo I CL I z <0 c.0 Z ca N a-t d A z I (L a 03 al Of ALL S IDE ALL StAWLlee V:Vkom - S Al OVEM40 r 5V uoes r ., BE SE, -T SA Of 0 . T�VF- EQUIP AND 0 fT,OT or- A"2- FT lbs aff4ched Firs MuSt be cb M specifift! and W4 aPPro C.D.F. g L;e,q —C'h REVIEWED BY BUTTE CO. FIRE DEPT. CALIF. DEPT. of FOREST RY ❑ approved as submitted approved with conditions r)er attach eid sheet. bbA Signature Date 0,9� ,qc, ds el 0-� C. L/ r',7 NOTE: See thO attached Residg.hbal QOngtiudg Regui 'ments 1;.Pages We'll V-71 3 0, c) 0 02- 32 3Z- 13 A at ffn COUNTY on BURDW DEPARTMEW APPR,�7ED 058 - 'l20 — 0 -5 01 /'. 1 9- fp s. Q�� V6� e - A 1I I J ,0-0 / 14 7-6 159/ APPROVED Butte County Environmental Health to it BSE COUIV SU'LDINGDEPAIR 7Y APp RQ`FD amolumn-MUMMI: mFo-------- F.M; a- AREA 10 MI Mnu�mmmmmmmmmmmmm "m 1191"m NMI 6pr RECESSED ENTRY le. OPT. PEN W-10"XIZ-10" PR X z WU17/JUN02 WU17/JUN02 Exterior • Fiber cement siding built to resist weather damage • Full 3:12 roof pitch for exterior eye -appeal • 2" x 4" exterior wall construction provides a sturdy frame • Transverse floors with 2" x 6" floor joists for better support, • 36" inswing front entry door with deadbolt, peephole and brass knocker for your family's safety • Inswing rear door with deadbolt and window add natural light Interior • Decorative vinyl covered sheetrock wall panels that are easy to clean • Standard 17 oz. carpet in all living and bedroom areas for high performance and low maintenance • Textured ceiling throughout (vaulted in some areas) provides an open look and feel Baths • Easy -care laminate countertop with hand laid, 4" ceramic tile backsplash provides attractive color accent • Recessed medicine cabinet provides. convenient storage space in each bath • Ceiling exhaust fan provides extra ventilation in each bath • Window in each bath to provide natural light • Moen® single lever shower faucets • Moen® 4" dual lever faucets - "Buy it for looks. Buy it for life" Kitchen • Brand name appliances provide confidence and hassle4ree service - 30" free standing gas range - 14 cu. ft: frost -free refrigerator • Moen® single -lever metal faucet • Bank of 4 drawers provides convenient storage for your utensils • Double cell porcelain sink adds flexibility in kitchen activities • Elegant crown molding provides a finishing touch to overhead cabinets Utility, Safety and Energy Features • 30 gallon electric water heater is efficient and requires low maintenance • Coleman® gas furnace provides name brand confidence and hassle -free service • Overhead utility shelf for added storage space • Zone II insulation package for energy efficiency includes: Low -E white vinyl framed, dual -paned windows, R722 ceiling, R-1 1 wall, R-11 floor • Shut-off valves at all, plumbing fixtures. for your convenience ' • -Plumb/wire for washer and electric dryer provides convenient hook-up Note that square footage is measured from exterior wall to exterior wall, and is an approximate figure. Length indicated in floorplans is floor length only. Renderings and diagrams are meant to be representative and, in keeping with Fleetwood's policy of constant updating and improvement, may vary from the actual home. All dimensions are nominal Ask your retailer for specifics. (Add four feet to arrive at transportable length.) _ PRICES AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE OR OBLIGATION. ® 01996 Optional Features • Dishwasher and garbage disposal for quick and easy kitchen clean-up • Skylights of various sizes brighten any room • Recessed entry adds charm and distinction to your home's exterior • Refrigerator and range upgrades meet your culinary needs • Deluxe carpet selections for increased performance and beauty . • '/z' rebond carpet pad extends the life of your carpet • Ceiling fan circulates air for a "spring breeze" feeling all year long • One-piece fiberglass tub/shower combinations are beautiful and easy to clean • Wood burning fireplace creates'a warm, cozy home environment • Dormer options create a variety of charming exterior looks • Increased roof loads are designed for the demands of mountain areas • Sliding glass exterior- door welcomes more natural light into your home • 30 and 40 gallon gas water heaters provide energy efficient hot water for your family's needs • Zone III insulation package to meet the needs of the climate where you live, includes: white vinyl, dual -paned windows, 2" x 6" exterior walls with R-33,19,22 insulation AW FLEETWCOD. FLEETWOOD HOMES of CALIFORNIA, INC. a subsidiary of Fleetwood Enterprises, Inc. 18 N. Pioneer, Ave., P.O. Box 1308 Woodland, CA 95776 1 (530) 662-3223 WU17/0ft? ,r 1. Owner's Name: VD 2. Assessor's Parcel Number: 0 039 3. Installer's Name: EK wj A l o e- 4Aornes 4. Is the site currently under, permit? Yes[ J No"" Permit No. 5. Is the site an existing site? Yes[ J NoVJ (If yes, furnish two plot plans). 6., What is the electrical rating of the. mobilehome? l DO Amperes. 7. What is the mobilehome site circuit breaker rating? Amperes. 8. What is the electrical rating of the mobilehome site? Amperes. 9. Is the main service remote from the mobilehome site? Yes[ J Nor ] If it is, what is the rating? Amperes. 10. Is there any other electric load to be served by the mobilehome site electric service (i.e. well, garage etc.)? Yesir ] No[ ] If yes, please identify the load and size: a) The mobile home site: Load- .,';aw :K P-%%—RAmperes- 3° b) The main service: Load- Ainperes- 11. Type of gas service at mobilehome site: Natural[ ] Propane[ -j] None[ J 12. Size of gas pipe at the mobilehome site from the meter or tank: 31 til inches. 13. What is the gas pipe length from the meter or tank to the mobilehome? 2 (ft.). 14. What is the mobilehome gas demand? B.T.U.*- *(This information is not required if the pipe length is less than 6 feet on natural gas or less than 50 feet on propane). THE OTHER SIDE OF THIS FORM MUST BE COMPLETED IN ORDER TO PROCESS THIS PERMIT APPLICATION BUTTE LOUR I APPROED May 1995 8.5 Mobilehome Manufacturer: tl` 6 CMA_ Manufacture Year: 0�6� If other than single wide, furnish Setup Model Number: 444 S_ � Width:Olo�R►r(ft.) Length:- i!(ft.) Tagalong or Expando Size On all mobilehomes manufactured after October 7, 1973, furnish manufacturer's installation manual and structural setup sheets. FOOTINGS: Wood pressure treated or foundation grade[v] Other: SUPPORTS: Concrete block]. Other: Provide Tie Down Specifications for all Mobilehomes: Pier Footings Sizes and Location SINGLE WIDE MULTI -WIDE Line 1 Line I Line 2 Line 2 ................................................:................................................ Main Beams Line 2................................................................................................ e2 Line I Line 3 Line 2 ................................................................................................ Main Beams ................................................................................................ Line 2 Line 1 ............................................... L�ine 5 Tag or Triple ine 4 ine 1 Line 1 Piers: Size minimum: x z'`1 i. Spacing maximum: From ends -maximum: ` Line 2 Piers: Size minimum: x [7U) ]. Spacing maximum: o ` From ends -maximum: ` 0 ` Line 3 Roof Loads: Size minimum Location (from front): Line 5 Roof Loads: Size minimum: Location (from front): Line 1 Openings Size minimum: ] x [ Each side of openings with width over: F7` Line 4 Piers: Size minimum:t,x Spacing maximum:From ends -maximum:` ( z�) ( 7:) 1'Lx 30 't`i�3o Zyx3o -",. 3o z4 x'3o Lo L NOT_ =2)' -� - 3f" -11 I " D0?' L.X3 1' A & A &T I REQT T I I 1N TAPE RECEPT: CPT L / / G� 1 "L n { ON UNDERSIDE i ®°���a I21 J/ OP c GPS =T� V I �SjOF fLGGR i 1>��NG DEPAR it At�p�! .I u I OPT "]' e 1 ; 4 a• J lY/H -)INING AREA %' I p pit r h�u `NK 9,1 U7� F:+TCNs BEDROOM =3 I 2041. 1^$p' / ., d� D"rF ag ? SQ FT. '"tltt V i, r d r^ I G — ,, l .,. 7 e�EP � ► L-7-- ' ' � , � 5 4 ' ��� LM` . H;. I ?�• I � < / „ I I GPT �� (REFER u% Ql�i Fl V i EGRESS �//- ` {�1 �I �P^ Iva wzl A' Z , JP f IOGG I 1 8" 32 7 22: 22 1 D i ��J 7'i3zT — COMBIKE HA 7000 3 15 t \ u r oI j4 I` 1 '2 �/l 7000 4_ 15'-Z' �'-2" cCK W a tV r CL4C A A 7 `� i33r ° 5 7'-10" 32 32, z ,� } i\ v 'Inacotes Er-rma is Rea6iredr__, DF 7, , STD SPT b i� $-OPT LErIP!C R00�' FEMERAL NAND AC UIRD, u G.� R 1'! i 30 LL. h _DR00Y, 41ECZSSEDr `; hoUSINGC' iRL•FION ! r 0 D. L. ,1 073 b SQ.FT. 1 Ei\ri_nT_(� !+ PnR00h' 4n :AF` fY ANDARDS I I fi)rj 7 7 136.0 SQ. - 'LOX} MAX. Ki. Sv' I 11'. • /• `rr�rR 7 '� JAG g 7r�r:i nc Iro.I RZI ' LLrN.r ��iYv i��. (DFUR L� 5 J L/zGa yam1'300 I I'-�•" 32 32 '� IZ A % —0" 2" 123 Q 17' -1G" 12'-4 5,00 C 7-10" 3232 << 28'-4" °109 3el 15'-2" 5 E tic 1) This loci may be bail cs cn excci mirror ySLt 1GTE {2; AIc q I-� imcre ubnut he lengUl and/or •aidth azie E. 1 5-2- 5 I a w7 2) A.-`,oi bibu:ory sidesid lenath has bemA I re: increwed Per offset design ccnfic¢roucm 50D�7 S el 7'-1U" 132 32j z V.lNDClib' /DOOR KhEDULEEI •.edro es 2' Eear:"- :6 lear?, c' I DESCs'<IT ON Ir r t4" PIT !v'^' J�RIPT1Ci; ' Ii t i V . z- D 7 ti'X3i H. R�i.;5�cscs.1 45"X58I V. SLIDER 115.2; 7.6 �CA)0LALr I 2 36':C3�?'* I V. SUDER, I 3.i 6.5 3 1 3L X 8 C F. -LANG(— J — CI � S8•. ii r 5X: 3 0 ,F_c. � JOR'Lh � 4 14'X40" I V. SUIDER ' 2.5: 1.7 I I ZI 1 Lnr f1 up..E e.R _-,Iru 7 ° 9'Xlo" I rIxM- 2.0: — I j L 0 In, cM-M,Zrz 0. C=b�G ti:0 "ori et: IT �� 9::c kE�. 12 ` 30":i40" I H. SJDER i 5.8! 3.2 I I �s L ca,,vc r:.,: s.,r -4 r c.;^f ,r ,,. 1 I I i © S!!C}r D,-=-. '1 a VOGUE -+SnNINN ' i I_9 DDu., e-1- L Td:.l.' nu—lJri.`I 6� GR:L c'1d.�• — _ u 2 0 . .. ... .�... _.. ,. ... �.. .,- L m .. ti 0 0 I NOT_ =2)' -� - 3f" -11 I " D0?' L.X3 1' A & A &T I REQT T I I 1N TAPE RECEPT: CPT L / / G� 1 "L n { ON UNDERSIDE i ®°���a I21 J/ OP c GPS =T� V I �SjOF fLGGR i 1>��NG DEPAR it At�p�! .I u I OPT "]' e 1 ; 4 a• J lY/H -)INING AREA %' I p pit r h�u `NK 9,1 U7� F:+TCNs BEDROOM =3 I 2041. 1^$p' / ., d� D"rF ag ? SQ FT. '"tltt V i, r d r^ I G — ,, l .,. 7 e�EP � ► L-7-- ' ' � , � 5 4 ' ��� LM` . H;. I ?�• I � < / „ I I GPT �� (REFER u% Ql�i Fl V i EGRESS �//- ` {�1 �I �P^ Iva wzl A' Z , JP f IOGG I 1 8" 32 7 22: 22 1 D i ��J 7'i3zT — COMBIKE HA 7000 3 15 t \ u r oI j4 I` 1 '2 �/l 7000 4_ 15'-Z' �'-2" cCK W a tV r CL4C A A 7 `� i33r ° 5 7'-10" 32 32, z ,� } i\ v 'Inacotes Er-rma is Rea6iredr__, DF 7, , STD SPT b i� $-OPT LErIP!C R00�' FEMERAL NAND AC UIRD, u G.� R 1'! i 30 LL. h _DR00Y, 41ECZSSEDr `; hoUSINGC' iRL•FION ! r 0 D. L. ,1 073 b SQ.FT. 1 Ei\ri_nT_(� !+ PnR00h' 4n :AF` fY ANDARDS I I fi)rj 7 7 136.0 SQ. - 'LOX} MAX. Ki. Sv' I 11'. • /• `rr�rR 7 '� JAG g 7r�r:i nc Iro.I RZI ' LLrN.r ��iYv i��. (DFUR L� 5 J L/zGa yam1'300 I I'-�•" 32 32 '� IZ A % —0" 2" 123 Q 17' -1G" 12'-4 5,00 C 7-10" 3232 << 28'-4" °109 3el 15'-2" 5 E tic 1) This loci may be bail cs cn excci mirror ySLt 1GTE {2; AIc q I-� imcre ubnut he lengUl and/or •aidth azie E. 1 5-2- 5 I a w7 2) A.-`,oi bibu:ory sidesid lenath has bemA I re: increwed Per offset design ccnfic¢roucm 50D�7 S el 7'-1U" 132 32j z V.lNDClib' /DOOR KhEDULEEI •.edro es 2' Eear:"- :6 lear?, c' I DESCs'<IT ON Ir r t4" PIT !v'^' J�RIPT1Ci; ' Ii t i V . z- D 7 ti'X3i H. R�i.;5�cscs.1 45"X58I V. SLIDER 115.2; 7.6 �CA)0LALr I 2 36':C3�?'* I V. SUDER, I 3.i 6.5 3 1 3L X 8 C F. -LANG(— J — CI � S8•. ii r 5X: 3 0 ,F_c. � JOR'Lh � 4 14'X40" I V. SUIDER ' 2.5: 1.7 I I ZI 1 Lnr f1 up..E e.R _-,Iru 7 ° 9'Xlo" I rIxM- 2.0: — I j L 0 In, cM-M,Zrz 0. C=b�G ti:0 "ori et: IT �� 9::c kE�. 12 ` 30":i40" I H. SJDER i 5.8! 3.2 I I �s L ca,,vc r:.,: s.,r -4 r c.;^f ,r ,,. 1 I I i © S!!C}r D,-=-. '1 a VOGUE -+SnNINN ' i I_9 DDu., e-1- L Td:.l.' nu—lJri.`I 6� GR:L c'1d.�• — _ CDF FIRE SAFE REQUIREMENTS AP# PERMIT # NAME Under authority of PRC 4290, the following checked items are required by the Butte County Fire Department and are made apart of this permit. These requirements are minimums and will be superseded by Butte County local regulations which equal or exceed these standards. Field inspections will be made by the Butte County Building Department for compliance. V1 1272.00 Maintenance of Defensible Space. To ensure continued maintenance of properties in conformance with these standards and measures and to assure continued avail- ability, access and utilization of the defensible space provided for in these standards, annual maintenance must be provide for by the land owner. Driveway Standards lyQ 1273.02 Surface. All driveway surfaces and structures (bridges, 1273.07 culverts and other apparteaant structures which supple- ment the roadway bed or shoulders) shall provide unob- structed access to conventional drive vehicles, includ- ing sedans.and fire apparatus weighing up to 40,000 pounds. I$J 1273.03 Grade. Not to exceed 16 percent unless paved. 1273.04 Driveway Radius 1. No roadway shall have a horizontal inside radius of curvature of less than 50 feet and additional sur- face width of 4 feet shall be added to curves of 50- 100 feet radius; 2 feet to those from 100-200 feet. 2. The length of vertical curves in roadways exclusive of gutters, ditches and drainage structures designed to hold or divert water shall be not less than 100 feet. N_ 1273.05 Turnarounds. If required, will have a minimum turning radius of 40 feet from the center of the road. �} 1273.05 Turnouts. Shall be a minimum of 10 feet wide and 30 I feet long with a minimum 25 foot taper. on each end. 1270.10 Width. All driveways shall provide a minimum 10 foot traf f is lane and unobstructed vertical clearance of 15 feet along its entire length. Page 1 of - 3 . g-72--37 02--3.2-92- located at least 30 feet from the AP # PERMIT # open to allow a vehicle to stop NAME [�] 1273.10 Turnouts. Driveways exceeding 150 feet in length, but less than 800 feet in length, shall provide a turnout near the midpoint of the driveway. Where a driveway exceeds 800 feet, turnouts shall be provided no more than 400 feet apart. 1273.10 Turnaround. A turnaround shall be provided at all building sites on driveways over 300 feet in length and shall be within 50 feet of the building. 1273.11 Gates [)�] 1. Gate entrances shall be at least two feet wider than the roadway it serves. [Xl 2. The gates must be located at least 30 feet from the roadway and shall open to allow a vehicle to stop without obstructing traffic on that roadway. 3. Where a one-way road with a single traffic lane provides entrance, a 50 foot turning radius shall be used. Fuel Modification 1276.01 Setback for Structure Defensible Space. 1)6 1. All parcels 1 acre aid larger shall provide a mini- mum 30 foot setback for buildings and accessory buildings from ul] property lines and/or the center of the road. [ ] 2. For parcels less than l acre, local jurisdiction shall provide for the same practical effect. See Other Requirements below. r(J 1276.02 Disposal of Vegetation and Fuels. Disposal; including chipping, burying, burning or removal to a landfill site approved by the local jurisdiction, of flammable vegetation and fuels caused by site development and construction, road and driveway construction and fuel modification shall be completed prior to completion of road construction )r fi:ial inspection of a building permit. Page 2 of 3 AP # PERMIT # NAME Other Requirements [ ] If Building Setback is 15 to 30 Feet: - Class A or B roof - Enclosed eaves [ ] If Building Setback is Less Than 15 Feet Choose any 3,of the following: - Metal or no doors on side toward property line with insuffi- cient setback - Class A or B.roof with enclosed eaves - Interior automatic sprinkler system per NFPA 13D - Glass area not to exceed 10W of wall area toward property line with insufficient setback - Siding from the following list: Stucco - 3 coat - Hardi-Board or Plank Masonry Masonry veneer. Metal Other Butte County Fire Department approved materials 12— Date 7Date Signature Page 3 of 3 VECTOR DYNAMICS FOUNDATION SYSTEM WIND ZONE 1 & 2 INSTALLATION INSTRUCTIONS For the State of California INDEX SECTION INTRODUCTION PIER HEIGHTS GENERAL INSTALLATION SET-UP INSTRUCTIONS METAL PIER & V -DRIVE PARTS LIST CONCRETE INSTALLATION SCHEMATICS PAGE 'NUMBER 3 4 5 & 5a 6 7, 7A, 7B & 7C 8&9 WIND ZONE I - SINGLE SECTION WIND ZONE II - SINGLE V -DRIVE - METAL PIER - DOUBLE SECTION - TRIPLE SECTION - SINGLE SECTION - DOUBLE SECTION - TRIPLE SECTION SOIL CLASSIFICATION 10 11 12 13 14 15 16 17 18 06adl zz /") b7- Release Date 8/13/2001 Engineer Approval 15070 MALTA Vaje %�g5' 18551 SUBJECT TO CORRIC T IONS NOTED APPROVAL DOES NOT AUTHORIZE OR APPROVE ANY OMISSIONS OR DEVIATION FROM REQUIREMENTS OF APPLICABLE STATE LAWS AND RF.GUI.AT:;1;:S State of CBlifomia Departrnent of Housing Od Community Develepr ent CL'ODES AND STANDARDS �z Date 9-/D—C)/ N0._ 1 /— /r - Plan Approval Expim 9 — / O - D For Further Information TIE DOWN ENGINEERING 5901 Wheaton Drive Atlanta, GA 30336 404-344-0000 FAX 404-349-0401 www.tiedown.com I Tie Down Engineering, Inc. VECTOR DYNAMICS INSTALLATION INSTRUCTIONS Introduction These instructions describe the proper use of the Vector Dynamics Foundation System in Wind Zones 1 & 2. Additional installation instruction is available in VHS video, from manufactured housing distributors or from Tie Down Engineering, titled, Vector Dynamics Installation Video. The Vector Dynamics foundation system supports the home by anchoring the two longitudinal main rails. The system is approved in Wind Zone I & II & III areas of the Manufactured Home Construction and Safety Standards and Wind Standards; Final Rule 24CFR part 3280 for both single and multi sec- tion homes. Instructions for Class 5, Sub Soil Conditions, (Wind Zone I & II), are available through local distributors of Vector Dynamics or directly from Tie Down Engineering. General The Vector Dynamics Foundation System provides the support to resist lateral and over -turning movement of the home as required by the Federal Manufactured Home Construction and Safety Standards in Wind Zones I & II when the system is used as described in these instructions. See manufac- tures Home Installation Manual for other pier & anchoringrhe uirements The following characteristics apply to both single and multi section homes: • Main rail minimum spacing of 86 inches or greater. • Nominal 8 foot or less top plate height at side walls. • Main rail depth of 12 inches or less. • Maximum roof slope of 20 degrees (4.4 in. in 12 in.) • Maximum pier height under main rail of 56 inches (see page 3). WIND ZONE I • Maximum single section home width is 16 feet including eaves; maximum eave width of 12 inches on each longitudinal side of home. • Maximum double section home width is 36 feet including eaves; maximum eave width of 12 inches on each longitudinal side of home. • Maximum triple section home width is 48 feet including eaves; maximum eave width of 12 inches on each longitudinal side of home. WIND ZONE II • Maximum single section home width is 15 ft. including eaves, maximum eave width is 6" per side. • Maximum single section home width of 16 ft. including eaves must use two additional vertical ties/ anchors/stabilizer plates (one per side) as listed in the charts on page 15. Maximum double section home width including eaves 32 ft., maximum 12" eaves per side • Maximum triple section home width including eaves 48 ft., maximum 12" eaves per side The Vector Dynamics Foundation Systems may be used as a part of the vertical or gravity support system considering that each set of Vector Dynamic pad (s) has two (2) or three (3) square feet bearing area. Piers not used as part of the Vector system shall be located and constructed in accordance with the home installation instructions and/or state standards. To inquire about the use of the Vector Dynamics Foundation Systems with homes of four or more sections or on homes requiring pier heights greater than 56 inches which are not included in these instructions, contact Tie Down Engineering, Inc. at 800-241-1806. The Vector Dynamics Foundation Systems may be used on homes which require pier heights not to exceed 56 inches under one or both main rail(s). See page 3. Note that a ground anchor is used at each Vector system location in Wind Zones II & III. The use of interlocked double stacks of concrete blocks may be required by the home manufacturer or the state. Check with the most recent regulations in California. The Vector Dynamics Foundation System has not been designed for use on exposure "D" homes. Exposure "D" homes are homes located within 1500 feet of the coastline. Additional vertical anchor ties that are unique to a home's design may be required by the home manufacturer. These locations include shear walls, mar- riage line ridge beam support posts, end frame ties and rim plates. The term end frame ties refers to the longitudinal ties that are attached to a home to resist wind load on the end walls. If longitudinal ties are required by the home installation instructions or other state standards, these longitudinal ties must be installed and connected to anchors that are independent of other ties and anchors. See separate. instructions for the use of Vector Dynamics with Tie . Down's Longitudinal Stabilization Device. The term rim plates refers to the factory brackets fastened onto the perimeter joist or specified as a location for vertical ties. c Page 2 California ®/2001 56 i ma: Maximum Pier Height (Wind Zones I & II only Figure The Vector Dynamics Foundation System may be used on homes which require pier heights not to exceed 56 inches under one or both main rail(s). Note that a ground anchor must be used at each side of a Vector system location in Wind Zone II, and where the pier heights exceed 24 inches on a single section home in Wind Zone I. Piers must be constructed in accordance with the manufacturer's installation instructions and/or state requirements. The use of interlocked double stacks of concrete blocks may be required by the home manufacturer or state. Check with the most recent regulations in your state. 56 ii mai r►gure z Unequal Pier Heights ( Wind Zones 1 & II ons i in. iax. Vector Dynamics may be used on homes with unequal pier heights of 56" or less under one or both main rails. The difference between the taller pier and the shorter pier cannot exceed 26". Note that a ground anchor must be used at each side of a Vector system installation in Wind Zone I and where either of the pier heights in that location exceeds 24 inches on a single section home in Wind Zone I. Only concrete blocks and pressure treated lumber compression members are permitted on unequal pier heights using the Vector system. Piers must be constructed in accordance with themanufacturer's installation instructions and/or state requirements. The use of interlocked double stacks of concrete blocks may be required by the home manufacturer or state. Check with the most recent regulations in your state.� Page 3 California /2001 GENERAL INSTALLATION INSTRUCTIONS SITE PREPARATION It is necessary that the home site be properly graded and sloped to prevent water and moisture from standing or flowing beneath the home. See manufacturer's home installation manual and state requirements for grading and other site preparation. FOOTINGS AND FROST LINES The Vector Dynamics Foundation System can be placed directly on top of the ground after clearing all loose vegetation. In areas where frost line/poured footers are required, the Vector system for concrete is used. See pages 8 & 9. FOUNDATION/FOOTING SPECIFICATIONS FOR VECTOR PADS Vector Pads must be used in place of conventional foundation pads for each Vector foundation system. Each (set of) Vector Pad(s) provides two or three square feet of pier bearing support. Vector Systems should be spaced as evenly as possible along the length of the home, with one Vector system within two feet of each end of the home. For pier locations in between the Vector Systems, use the foundation pads normally recommended by the home manufacturer and/or state requirements. Pier heights in excess of 24 inches or when unequal must follow instructions printed on page 3 of these instructions. Nominal 3-1/2 inch or 4 inch Schedule 40 PVC pipe or TDE steel compression strut (#59043) may be used only when the pier heights are similar on fairly level ground. Steel strut and PVC are not permitted when metal pier foundations are used. The adjustable galva- nized steel compression strut, #59043, is attached to each inside pad with a 1/2" X 2-1/2" grade 5 carriage bolt and can only be used with the swivel connector on strap. The grade 5 bolt attaches the swivel connector and the steel strut to the pad. When the swivel connector is used with a wooden or pipe compressive member, the vector diagonal connector should be part #59279 not #59276. After tightening the end grade 5 bolts, adjust- ment bolt is installed through the two square steel compression struts to lock them in place. Foundation pad size and pier spacing must be consistent with home manufacturers' instructions and/or state requirements. LUMBER/MOISTURE - TERMITE SHIELD To cut lumber (2 - 2x4's or 1 - 4x4 per Vector system) for the center compression section, when using con- crete blocks for piers, measure center to center -frame (I-beam) distance and subtract 16". When using METAL PIER STANDS, measure center to center frame distance and add 16". 3-1/2" or 4" nominal schedule 40 PVC pipe meeting ASTM D1784 or Tie Down's steel compression strut (#59043) may be substituted for lumber as the center compression strut under certain conditions described above. Pipe adapter bracket, part #59281 must be used with PVC pipe simultaneously with the Inside Tie Brackets, part number 59276. The pipe adapter bracket is used on top of the pipe and under the Inside Tie Bracket. In certain regions the optional Moisture Termite Shield may be required between the lumber and ground. ALL WOOD MUST BE PRESSURE TREATED, GROUND CONTACT RATED. Tip: Pre-cut your lumber and mark as to brand or model of homes you will be installing. If frame widths are the same, the pre-cut boards will also be the same length in each Vector set-up. STRAP TENSION All strapping must be tight upon assembly of the Vector system. Tests have been conducted with "hand tight- ened " strap in the Vector system to remove the need for specific tension specifications. Hand tight is defined as removing all slack with minimum of movement available when pressing on the strap. While subsequent tight- ening of the straps is not required, straps should be checked after any strong wind conditions, just as conven- tional anchor tie down straps should also be checked, to insure the maximum performance of the foundation system. A minimum of two factory 1/4" spot welds must be used when straps are connected to the swivel con- nectors with welds. Page 4 California 001 Set -Up Instructions for the Vector Dynamics Foundation System #59007 (Kit #59007 is interchanaeable with Kit #59018) 2. SET BLOCKS (OR PIERS) ON VECTOR FOUNDATION PADS Center the foundation blocks over the Vector pads. Place the pre-cut 4x4, 2x4's (side by side), Schedule 40 PVC (w/PVC adapter plate, part #59281) or 1 adjustable TDE steel compression member, (part #59043) tightly between the blocks, with ends resting on the Vector pads, and centered on each U -bolt. 3. OUTSIDE TENSION BRACKETS Attach an Outside Tension Bracket to the U -bolts on the outside of the foundation blocks and Vector pads. Place one of the short 6"- 2x4's between the bracket and Vector pad. Adjust the short 2x4 so that it pushes against the foundation blocks, removing any space between the piers and center compression section. Tighten the 3/8" bolts. 2 square foot pad placement or (1) 3 square foot pad 4. INSIDE BRACKETS AND STRAPS Attach the Inside Tie Brackets to the U -bolts over the pre-cut boards or PVC. Attach a strap with hook to each inside tie bracket. Tighten bracket. When using looped strap and a crimp seal, in place of the hook, place a 3" long section of strap, folded in half and inserted between the strap and inside tie bracket. Place other end of strap over the opposite (- beam and continue down to outside of the foundation blocks. Attach the strap to the Outside Tension brackets using the slotted bolt and nut provided. Wind strap a minimum of five times around the bolt. Continue tightening the slotted bolt until all slack has been removed and the strap is tight. 5. SET ANCHORS Refer to section home drawings for anchor installation information. Stabilizer plates are required for diagonal ties only. Preload anchor against stabilizer plate. Make certain all slack is removed and strap is tight. For single section homes in rocky soil conditions in Wind Zone 1 only (Soil Classifications 2 & 3 only), use minimum of 3 each V -Drive anchors per side. See drawing on page 6 for placement. 111�4 Page 5 California A001 Set -Up Instructions for Vector System #59018 (Kit #59018 is interchangeable with Kit #59007) A - o ro 1 f f Jr ,v Long U-® 1. Set Vector Pads Clear all vegetation where pads will rest. Place a long U -bolt in pad as shown. Press or ham- mer pad into the ground. 2. Set Block or piers on pads. Center foundation blocks or piers on pads. Place pre-cut center compression member between blocks, resting on pads, centers between U -bolts as shown. 3. Outside Tension Bracket Attach outside tension bracket as shown to out- side of pads. 4. Inside brackets & straps Attach the inside tie brackets to the U -bolts over the compression member. Attach a strap w/hook or swivel strap w/nut/washer & bolt (washers are required). Place other end of the strap over opposite I-beam & down to outside tension bracket. Cut strap 12 - 15 inches past bracket. Attach strap & slotted bolt in bracket. Tighten strap until tight with 4-5 wraps around bolt. Repeat with opposite strap. Page 5a California /2001 Vector Dynamics Metal Pill En For metal piers, place the piers in the center of the Vector pads. Set the single 44 or two 2x4's through the piers, centered in the U -bolts, so that the board(s) overhangs the Vector pads on each side by about 2'. Outside Tension brackets attach the same. Inside tie brackets mount 'upside down' as shown in drawing. Metal piers using the Vector system can only be used on level ground installations. Conventional pier adjusters must be placed under beam with upturned edge directed towards the outside of the home. Pier capacity rating and spacing must be consistent with home manufacturers' installation instructions and/or state requirements. When using METAL PIER STANDS, cut lumber (2 - 2x4's or 1 - 44 per Vector system) for the center compression section, by measuring center to center frame distance and adding 16'. Optional Moisture Termite Shield may be required in certain regions. ALL WOOD MUST BE PRESSURE TREATED, GROUND CONTACT RATED. Adjustable steel strut (#59043) and PVC Schedule 40 pipe are not permitted to be substituted for lumber when using metal pier stands. V -Drive System for rocky soil Installation: conditions ::- V -Drive anchors are used only with OjA7Zone I, single section homes. Soil Class 1,2,& 3. V -Drive anchors are used only in Wind Zone I, on single section homes in areas where rocky soil conditions do not allow a conventional helix style anchor to be installed. For solid rock, Soil Class 1, predrilling of holes for the V -drive rods is recommended. Vector Systems are set following the general set up instructions provided. With the V -Drive anchor, the short 2x4 boards used with the outside tension brackets are discarded. In place of the short 2x4's, a longer 2x4 is used as per the diagram above. This 2x4 board should extend from the base of the Vector pier set to 5 inches from the side wall of the home. Place the V -Drive head over the end of the longer board. Using a heavy hammer or electric hammer gun, drive the three V -Drive anchor rods through the V -Drive heads at an angle of approximately 45 degrees under the home. The rods must come to a complete stop on the V -Drive head. Attach a strap with hook, buckle or beam clamp to the frame and attach to the V -Drive head with a slotted bolt. Cut the strap end about ten inches Daq the anchor head to allow at least five wraps around the slotted bolt. Continue tightening strap until all slack is out and strap is tight. ` Page 6 California �M-001 Vector Dynamics Foundation Systems a =ics Component Parts List ° ° T Y Vector System 2000 Kit # 59018 o Single piece pads with straps ® and slotted bolts �� o0 Part #'s included: 59310, 59288, 59135, 10925, 59279, 83044z, 59232 & 59732 e 4 Vector System Q e Kit # 59007 I� Part #'s included: 59275, 59282, 59276, 83044z & 10999 Concrete Vector System 0 0 o Kit # 59008 (for single stack blocks) Part #'s included: 59277, 59282, 10530, 83044z, 59279 & 59232 Pan #'s included: 59273, 59282, 10530, 83044z, 59232 & 59279 Concrete Vector System Kit # 59006 (for double stack blocks) Page 7 California Vector Dynamics Foundation systems Component Parts List 00 ro-ho <t 0 Part #'s included: 59281, 59288,10925, 59232 & 83044z Vector 2000 3 Sq. Ft. Pad Part # 59271 1 required with 59026 Longitudinal System 2 required with 59024 Lateral System Vector Lateral Hardware Kit Kit # 59024 (for use with 59271) o n , V Drive Anchor Kit Kit # 59287 (for use with Kit#59007 only) ®o c ®o 0 Part #'s included: 59269, 59113, 59282 & 10999 Adjustable Steel Compression Strut P/N 59043 Or these products available at your local hardware store `<ee"Iedl ISSN) aA x A lP�e Qa��e `I 2ea'2X QOQVGQ\pe a�\e A" C A. Schedule 40 PVC pipe: 3-1/2" or 4" nominal schedule 40 polyvinyl chloride pipe or conduit made from type 1, grade 1, with cell classification 12454 as defined in ASTM D1784. Compound dimensions and tolerances in accordance to the requirements of ASTM D1785D. Color can be gray or white. Outside diameter is 4 inches. B. Ground Contact Rated Wood: No. 2 yellow pine or equivalent, pressure treated to AWPACI-1990 mini- mum, stamped "Ground Contact Rated" on wood or on label attached to the wood when purchased. ec Page 7A California /2001 Vector Dynamics Individual Component Parts Detail Vector Dynamics Single Block Pad Part # 59275 1 Sq. Ft. 12 gauge, used in pairs 16-3/16" X 9" x 2-9/16" Vector Dynamics 2000 Single Block Pad Part # 59310 2 Sq. Ft. 12 gauge 18.719" x 15.625" x 3" Vector Dynamics Single Stack Concrete Pad Part # 59277 12 gauge 17-1/4" x 11" x 5-5/16" Vector Dynamics Double Stack Concrete Pad Part # 59273 12 gauge 18.75" x 18.625" x 5.188" Vector 2000 3 Sq. Ft. Pad Part # 59271 - 12 gauge 22.5" x 19.418" x 3" Vector Dynamics Tension Link 4t•• Slotted Bolt Part # 59282 Part # 59135 6.25" x 2.52" x 3" VO 3" x 5/8" Vector 2000 Tension Link Long U -Bolt w/Nuts &Washers Part # 59288 Part.# 83044Z 2.125" x 2.375" x 2.06" 3/8" x 4" (16 Threads Per Inch) Concrete Wedge Anchor ® ® Short U -Bolt w/Nuts & Washers Part # 10530 Part # 10999 3/8" X 3-1/2" 3/8" x 3" (16 Threads Per Inch) 1 o Protecto-Strap Carriage Bolt w/Nut & Washer e Part #59276 p Part # 10925 6.3" x 3.3" x 7/8" ® 1/2" X 2-112" Strap Protectors as ProtectoStrap Part # 59232 Part # 59279 6.3" x 3.9" x 7/8" PVC Adaptor Part # 59281 ® Carriage Bolt w/Nut & Washer 7.25" x 4/56" x 1.42" Part # 10624 3/8"-16 x 4.5" Page 7C Caliform TIE DOWN . UNEERING Tie Down Marked & Certified G60 Galvanized Strapping Model Part # Length MS35 59150 35' MS37 59155 37' Tie Down Marked & MS42 59160 42' Certified G120 MS60 59165 60' Strap w/Swivel Connector MS600 59170 600' Part # Length 59732 12' p 59734 14' o- 59736 16' Frame Tie w/Hook 8 ft. P/N 59195 Earth Anchors 10 ft. P/N 59210 o x 12 ft. P/N 59211 Longer Lengths Available 0 30" x 3/4" with 2-4" helix Black Paint: Part #59095 Galvanized: Part #59079 Earth Anchor Stabilizer V Drive Head = n< : 12" wide Part #59269 y;.,. - Black' Paint: Part #59292 Galvanized: Part #59294 .m Drive Rods 8 u ® Part #59113 0 Page 7C Caliform TIE DOWN . UNEERING Vector Dynamics System for Concrete Applications Instructions for Vector Kit #59008 (for single stack blocks) sector � or Vector Kit #59006 (for single or double stack blocks) Page 1 of 2 These instructions are an addendum to the standard Vector Dynamics instructions. Read and follow all applicable instructions and guidelines in the Vector instructions and home installation manual. The Vector system for concrete pads applies to concrete footers, runners and slabs. Minimum size of concrete per Vector pier is 24" x 24" x 4"(for part #59006 or 59008) or 18" round X 12" deep (for part # 59008 only). The bottom of footers must be below the frost line or a minimum of 4" below finished grade whichever is greater. Concrete must be a minimum of 2500 PSI and sufficiently cured and set to accommodate an anchor bolt to its' full load resistance. 1. Determine location of pier sets where the Vector systems will be located. 2. Place one Vector concrete pad (gaiv. metal) on the concrete where the pier will be located, centered under the I-beam of the home. Place the upturned edge towards the center of the home and directed to the opposite Vector pier. Do the same for the opposite Vector pier. 3. Measure the distance between the two Vector system pads at the base where the Vector pad meets the concrete. Cut two ground treated 2x4's this length and place between the piers as shown. 4. Place a long u -bolt under the 2x4's and through the holes of the Vector pad as shown. 5. Place the concrete pier blocks on the Vector pad. Center the blocks under the frame. The upturned edge end of the Vector pads should be up against the inside of the pier blocks. 6. Build vector piers but do not wedge at this time. 7. Using a concrete drill bit, drill two 3/8" diameter holes on each side into the concrete using the holes in the Vector pad as a guide. Drill the holes 3 inches deep. 8. Place an outside tension bracket on the Vector pad as shown in Illustration one. Line up the holes in the bracket, Vector pad and concrete pad. Vector p for concret Wood Cap and wedge Outside Tension Bracket Wedge 8/2001 Concrete footer Page 8 California Vector Dynamics System for Concrete Applications Instructions for Vector Kit #59008 (for single stack blocks) sector or Vector Kit #59006 (for single or double stack blocks) Page 2 of 2 9. Put a washer and nut,on one of the 3/8" x 3-3/4" wedge anchors provided. The nut should be screwed on enough to have 1 or 2 threads showing on the top of the bolt. Place the wedge end of the bolt into one of the holes, going through the outside tension bracket, metal Vector pad and into the concrete. 10. Using a hammer, tap the wedge bolt into the hole. Maximum height for expansion bolt above concrete is".2". 11. Repeat for the other hole in the outside tension bracket and the two holes on the other Vector system pier set. 12. Place an inside tie bracket over the u -bolt so that the lip of the bracket is between the Vector plate and concrete blocks. Place washers and nuts on each U -bolt. Do not tighten yet. 13. Attach a strap with hook or crimp seal to the inside tie bracket, with sufficient length to go over the opposite pier and down to the outside tension bracket, plus 12 inches for wrapping the slotted bolt. Repeat for the opposite side. 14. Tighten inside u -bolts at this time. 15. • Use the outside tension brackets to remove any space between the outside tension brackets, concrete blocks and the inside edge of the Vector pad, by tapping the brackets with a hammer. 16. Wedge the pier set at this time. 17. Using a 9/16" socket wrench, tighten all of the wedge/anchor bolts, securing the outside tension bracket and Vector pad to the concrete. 18. Using a slotted bolt in the outside, tension brackets, insert strap through slotted bolt with end of strap aligned with outside edge of bolt. Turn slotted bolt until straps are tight using at.least five turns on the slotted bolts. Illustration Two Vector pad e for concrete Inside - Tie Bracket - 1, Concrete Compression f boards J U -bolt Page 9 9 California 6/2001 WIND ZONE I ' Vector Dynamics Systems Required I \ V \\ for Single Section Homes I I 1 (Materials Required) a1e�airl'a-tt^i\-\001e �nm. �e \ecy- secJiomu_a-l p9al Sacin le'J s 91e os9�gbe to 100 st tratoshowmu cln an� I 1 (a ax. tYP.CDCD Ani WIND ZONE I o (not to scale) W .t 00 I-LiN 0 2 sq. ft. padj Soil Classifications: Soil Bearing Capacity: Anchors Required': maX o c.tyP 34 tt. NOTE: Vector Systems should be spaced as evenly as is practicable along the length of the home. Pier spacing must be consistent with home manufacturers' installation instructions and/or state requirements. Maximum allowable working drag load for the Vector System with the steel compression strut is 2, 3, 4A, & 48 3,150 pounds per K2 Engineering test report. 1,000 PSF minimum 30" with 4" helix anchor (59095),12" stabilizer plates (55292), 1-1/4" frame ties w/4725 lbs. min. breaking strength. Home Length Vector Systems Required Anchors Required ' Per Side ' 0 to 72' 3 2 73 to 90 4 3 Each Vector Foundation System requires Y One \kctor Kit, 2 slotted bolts Y 2 ea. 1-1/4 in. lies, length will vary with pier height (4725 Ib. min. break), Y 1 ea. 4 x 4 pressure treated wood compression member Y or 2 ea. 2 x 4 pressure treated wood compression member Y or 1 ea. 3-1/2" or 4 nominal SCH 40 PVC ' Anchor and stabilizer plate combinalion pipe compression member Y or 1 TSE adjustable steel strut WIND ZDNE I _ Vector Dynamics Systems Required Single Section Homes Difficult Soil Conditions Sec\\Oo hoys elnsal goi \Jecko de�tnes ano n - 1 pE a � 2 rat sP g' fge�nstatta�lon 1 ' - - - - �XatnP�hoWs gen5l be to Ino 111�sk0k%onsPacin9 rno dation QJ aa''x. - r " (0� 2 CD ` 'k- O 3 N 0 O R max, o c.ryP I � _ NOTE: Vector Systems should be spaced as evenly as is practicable along the length of the home. Pier spaciV must be cortsistent with home manufact rers' itsWation Instructions and/or state requirements. Maximum allowable working drag load for the Vector System with the steel compression strut Is 3,150 pounds per 2 3 the K2 Engineering test report. 1,000 PSF minimum "V" Drive Anchor, Part Number 59269 1-1/4" frame ties w/4725 lbs. min. breaking strength. Wh ! V -Drive anchors are used only in WIND ZONE I (not to scale) Soil Classifications: Soil Bearing Capacity Anchors Required': Home Length Vector Systems Required Anchors Required Per Side ' 0to72' 3 3 73' to 90' 4 4 an us ng V Orrve Anchors Each Vector Foundation System requires One Vector Kit, 2 "V' Drive Anchors, 4 slotted bolts 2 ea. 1-1/4 in. lie, length will vary with pier height (4725 Ib. min. break), 1 ea. 4 x 4 pressure treated wood compression member or 2 ea. 2 x 4 pressure treated wood compression member or 1 ea. 3-1/2" or 4- nominal SCH 40 PVC pipe compression member (centercompression member only) ' "V" Drive Anchor, Part Number 59269 or 1 TOE adjustable steel strut 2 ea. 2x4 pressure treated wood for 1 V- Drive Anchor connection. 2 sq. ft. pad Note: PVC pipe cannot be substituted for wood on the -V' Drive Anchor connections. -�flif DOWN mclNrrelaa Metal Pier Sets - ZONE I ' Vector Dynamics Systems Required for Single Section Homes Up to 72 ft. (Materials Required) ' � home tttron msa\systanU\e seecto. m ,2{coc;'95atat a7t spom1 EXamsphogenbe to h s must WUSUaonpacIn9 n Pads - ` - - N, _ _ '2tt. max. tyR n ty 0 ZONE �2 sq. ft. pad 3434 t/ c tyP Soil Classifications: 2, 3, 4A, & 4B Soil Bearing Capacity: 1,000 PSF minimum Anchors Required: 3/4" x 30" with 4" helix anchor (59095) 12" stabilizer plates (55292), 4 ea. 1 1/4" frame ties Materials: Each Vector Foundation System requires one Vector Kit, 2 slotted bolts 2 ea. 1-1/4 x 12 ft. ties (4 725 Ib. min. break) 1 ea. 4 x 4 wood compression member or 2 ea. 2 x 4 wood compression member Home Length Vector Systems Required Anchors Required Per Side ' 0 to 72' 3 2 73' to 90' 4 3 Hncnor ana stabilizer plate combination NOTE: Vector Systems should be spaced as evenly as is practicable along the length of the home. DOWN f fIGlNIIffING: C Iv O v WIND ZONE I - Vector Dynamics Systems Required _ " - " - - elk Sy ems \ gu�dei`�es for Double Section Homes - ' ' " " - It doubt 9 t �e;;ak'%o (na�ua " 1e 0{ a ene(a1 sPahome ins<a (Materials Requiredl " - EXa. sh°Ws gust be to 111Pads , All — - -- 2n•m ` Maximum allowable working drag load for the Vector System with the steel compression strut Is 3,150 pounds per the K2 Engineering test report. 0 0 • �2 sq. ft. padr ' `JJ 44 NOTE: Vector Systems should be spaced as evenly as is practicable along the length of the home. Pier spacing must be consistent with home manufachrers' installation instructions and/or state requirements. Soil Classifications: 2, 3, 4A, & 4B Soil Bearing Capacity: 1,000 PSF minimum Anchors Required: None (marriage wall anchors may be required by home manufacturer) Home Length Vector Systems Required 0 to 48' 2 48' to 71' 3 72' to 89' 4 Each Vector Foundation System requires One Vector Kit, 2 slotted bolts 2 ea. 1-1/4 in. ties, length will vary with pier height (4725 Ib. min. break), 1 ea. 4 x 4 pressure treated wood compression member or 2 ea. 2 x 4 pressure treated wood compression member or 1 ea. 3.1/2" or 4" nominal SCH 40 PVC pipe compression member or 1 TOE adjustable steel strut �nE DOWN INWNIffIN( (D A 0) 00 N O O WIND ZONE 1 Vector Dynamics Systems Required- _ -lines for Multi Section Homes r "__-- oWsg�rbejhOmelons�a;\a�onn`anua (Materials Required) nSh. m�5 - , Soil Classifications: 2, 3, 4A, & 48 Soil Bearina Caoacity: 1-000 PSF minimum WIND ZONE 1 I -F-0. WON -1110 g. NOTE: Shear wall, ridge beam support posts & marriage wall straps & anchors may be required by the home manufacturer. Vector systems should be spaced as evenly as Is practicable'along the length of the home. A two foot variance + or - Is allowable at each system.Pler spacing must be consistent with the home Installatlon manual. \2 sq. ft. pad/ Maximum allowable working drag load for the Vector System with the steel compression strut Is 3,150 pounds per the K2 Engineering test report. Materials: Each Vector foundation system requires One Vector Kit 2 ea. 1-1/4 in. ties (4 725 lb. min. break) 1 ea. 4 x 4 wood compression member or 2 ea. 2 x 4 wood compression member or 3.1/2" or 4" nominal SCH40 Pipe compression member or 1 TOE adjustable steel strut Anchors Required Home Length Vector Systems Required Per Side Homes up to 48' 2 Vector Foundation Systems 0 Homes over 48' 3 Vector Foundation Systems 0 up to 52' - Homes over 52' 4 Vector Foundation Systems 0 up to 76' WIND ZONE 1 I -F-0. WON -1110 g. NOTE: Shear wall, ridge beam support posts & marriage wall straps & anchors may be required by the home manufacturer. Vector systems should be spaced as evenly as Is practicable'along the length of the home. A two foot variance + or - Is allowable at each system.Pler spacing must be consistent with the home Installatlon manual. \2 sq. ft. pad/ Maximum allowable working drag load for the Vector System with the steel compression strut Is 3,150 pounds per the K2 Engineering test report. Materials: Each Vector foundation system requires One Vector Kit 2 ea. 1-1/4 in. ties (4 725 lb. min. break) 1 ea. 4 x 4 wood compression member or 2 ea. 2 x 4 wood compression member or 3.1/2" or 4" nominal SCH40 Pipe compression member or 1 TOE adjustable steel strut WIND ZONE II (Hurricane) Vector Dnamics Systems Required for ingle Section Homes __-_-:;.-'- " Orme es (Materials Required} -- - f� S;ng�e Sod;;° Ghon �anual guldelin. Xamp\ejr\o fs gene; ' oahome install llluEratnd S9 ting mus datlon Pa Fours _ C7 v WIND ZONE II (not to scale) N� 7 • I 00 — O C �2 sq. ft. pad Home Length tyP Anchors Required 'NOTE: For single section homes 2tl.R`ax _ - - - with eaves that exceed 6 inches _ in Zone 2, two additional frame 5 tie anchors with stabilizer plates 5 (one anchor and one plate per 6 side) must be installed in additon 6 to the number of anchors listed 7 in the chart below. 7 Maximum allowable working drag load " 8 for the Vector System with the steel Soil Classifications: 2, 3, 4A, 8 46 compression strut Is 3,150 pounds per the K2 Engineering test report. Soil Bearing Capacity: 1,000 PSF minimum Anchors Required': 30" with 4" helix anchor (59095), 1-1/4" vertical ties w/4725 lbs. min. breaking strength. Home Length Vector Systems Required Anchors Required Eaves 6" or less Eaves over 6" less than or equal to 12" 0 to 48' 4 4 5 49' to 60" 5 5 6 61' to 72' 6 6 7 73" to 84' 7 7 8 85' to 90' 8 8 g Vector Systems should be spaced as evenly as Is practicable along the length of the home. Pier spacing must be consistent with home manufacturers' Instructions and/or slate requirements. Each Vector Foundation System requires One Vector Kit, 2 slotted bolts 2 ea. 1.1/4 in. ties, length will vary with pier height (4725 Ib. min. break). 1 ea. 4 x 4 pressure treated wood compression member or 2 ea. 2 x 4 pressure treated wood compression member or 1 ea. 3-1/2" or 4' nominal SCH 40 PVC pipe compression membe r r or 1 TOE adjuslable sleel Slrul ty (C (D rn 0 Iv CD N 0 0 WIND ZONE II Vector Dynamics Systems Required - - - - - " " �1io� hofs ems :�delinea;l for Double Section Homes - - - " b1e Se toO\Jecksy anuat g (Materials Required) a �2 (� d pactn9 lot ta\�at;°n m_ EXafnP�s o\Ns ge net � be to h°me �111usUan-tons sig mu_ gads an _ . I 1 _ --- i \ Irr� -- • 1 ♦ I — — � 2 ax.hP� ♦ ♦ I Maximum allowable working drag load for the Vector System with the steel compression strut Is 3,150 pounds per the K2 Engineering test report. NOTE: Vector Systems should be spaced as evenly as Is prac the length of the home. Pier spacing must be consisle manufacturers' Instructions and/or state requirements Soil Classifications: Soil Bearing Capacity Anchors Required`: 2, 3, 4A, & 4B 1,000 PSF minimum 30" with 4" helix anchor (59095), 1-1/4" vertical ties w/4725 lbs. min. breaking strength. Home Length Vector Systems Required Anchors Required Per Side 0to48' 4 4 49' to 60" 5 5 61' to 72' 6 6 73" to 84' 7 7 85' to 90' 8 8 Each Vector Foundation System requires One Vector Kit, 2 slotted bolts 2 ea. 1-1/4 in. ties, length will vary with pier height (4725 Ib. min. break). 1 ea. 4 x 4 pressure treated wood compression member or 2 ea. 2 x 4 pressure treated wood compression member or 1 ea. 3.1/2" or 4" nominal SCH 40 PVC pipe compression member or 1 TIDE adjustable steel Strut WIND ZONE 2 Vector Dynamics Systems Required 3 Section Homes (Materials Required) Maximum allowable working drag load co for the Vector System with the steel compression strut Is 3,150 pounds per v the K2 Engineering test report. n ty O 7 SV WIND ZONE 2 �eOt�nVeo°�sYa" at guide�lne5 ` �I I. ample 0e^efaLsP tiame tnstat�auon I . son 4 mist be to I ou^ ^ Pads I .'F datio . I .. 11.7 � � I � � 1 I ` I _ � I � � I ` � I NOTE: Longitudinal stabilization Is required. Vector systems should be spaced as evenly as is practicable along the length of the home. Pier spacing must be consistent with the home Installation manual. 2 sq. ft. pad Materials: 'Anchors Required: Soil Classifications: Soil Bearing Capacitv: 2.3,4A,&4B 1.000 PSF minimum Home Length Vector S stems Re ulred Y q Anchors Required Per Side Homes up to 48' 4 Vector Foundation Systems 4 Homesover 49' 5 Vector Foundation Systems 5 up to 60' Homes over 61' 6 Vector Foundation Systems 6 up to 72' Homes over 73' 7 Vector Foundation Systems 7 up to 84' Homes over 85' 8 Vector Foundation Systems 8 up to 90' 3/4" x 30" anchor (59095), with vertical straps Each Vector foundation system requires One Vector Kit 2 ea. 1-1/4 in. ties (4725 lb. min. break) 1 ea. 4 x 4 wood compression member or 2 ea. 2 x 4 wood compression member or 3-1/2" or 4" nominal SCH40 Pipe compression member or 1 TIDE adjustable steel strut VECTOR DYNAMICS INSTALLATION DESIGN INSTRUCTIONS This Vector Dynamics Foundation system instruction is applicable only on homes set on soils classified as Class. 4A 4B, 3 and 2 as described in the table below. For separate instructions for sub -soil, Class 5 conditions (above 50 in. lbs.), contact Tie Down Engineering. SOIL CLASSIFICATIONS Soil Class Types of Soils Blow Count (ASTM Soil Test Probe (1) D1586) Torque Value (2) 1 Sound hard rock...... NA NA Very dense and/or 40 -up More than 550 in. lbs. cemented sands, coarse 2 gravel and cobbles, preloaded silts, clays, and corals - Medium -dense coarse 24-39 350-549 in. lbs. 3 sands, sandy gravels, very stiff silts and clays 4A Loose to medium dense 14-23 275-349 in. lbs sands, firm to stiff clays 4B and silts, alluvian fill 175-275 in. lbs Peat, organic silts, 0-14 175 in. lbs 5 inundated silts, loose fine and lower sand, alluvium, loess, varied clays, fill, fly ash. (1) The purpose of the soil test probe is to gage the strength of the soil below the surface and near the anchor's helical plate. The strength of the soil is estimated in terms of its' resistance to penetration (flow) under load by means of the torque probe and is measured in inch lbs. The test probe has a helix on it. The overall length of the helical section is 10.75 in.; the major diameter is 1.25 in.; the minor diameter is 0.81 in.; the pitch is 1.75 in. The shaft must be of suitable length for anchor depth. (2) A measure synonymous with moment of a force when distributed around the shaft of the test probe. Information about geographical areas of termite infestations which might require the optional termite and moisture shield when a wood compression member is used may be obtained from the local building official or may be found in the 1995 edition of the One and Two Family Dwelling Code o� Page 18 California 8/2001 SITE PLAN REVIEW APPLICATION MXY 3 3 2002 Date: AP# J — �� _,2_A � L Permit Number (if applicable) 0 rLo tnv. APPLICANT INFORMATION Parcel Size: f I S At %(� Owners Name: Owners Address: Ol �'� S l 1i ``fin }� { 1►„� Telephone No.: Z L1 1 - 38 b Situs Address: 1 Co ,� 7 Proposed Use: Residential ❑ New Single Family Residential ❑ Single Family Addition ❑ Mobile Home ❑ Residential Accessory ❑ Permanent Second Dwelling ❑ Temporary Mobile Home (Aunt Minnie) ❑ Temporary Travel Trailer ❑ Multi -family Non-residential ❑ New Commercial ❑ Commercial Addition ❑ New Industrial ❑ Industrial Addition ❑ Single Family Remodel ❑ Commercial Remodel ❑ Industrial Remodel Other Septic ❑ Well Agricultural Exempt Building ❑ Other: Brief Explanation (if necessary): DO NOT WRITE BELOW THIS LINE DEVELOPMENT SER VICES INFORMATION (For Staff Use) ❑ Approved Conditionally Approved. ❑ Resolve Problems Prior to. Approval ❑ Site Plan Stamped Approved By LA2 Date Page I o f 5 ALL ITEMS CHECKED APPLY TO THE PROPERTY Parcel Is In: A Snow Load Area: •2-00© T,0 213 ej io -(-: j ❑ Land Conservation Act Minimum Acreage: ❑ Verify residence can be built per contract ❑ Nitrate Action Plan (See Environmental Health for standards) ❑ Watershed Protection Overlay Zone (See attached standards and requirements) ❑ Expansive Soils (Test for expansive soils and if verified proper foundation design required) ® SRA - (CDF to determine specific requirements) ❑ 100 -Year Flood Plain: (See attac ej) • Flood Zone: ' • Flood Panel No.: O i� 0� �. Index Date: 9 ❑ Sacramento River Reclamation District (Approval must be obtained from the California Reclamation Board) ❑ Feather River Reclamation District (Approval must be obtained from the California ReclamatimBoard) ❑ North Chico Specific Plan (See Development Fees Section and attached standards and requirements) ❑ -Chapman/Mulberry (See attachedstan dards and requirements) ❑..Cohasset Area (See attached standards and requirements) Use Requires: ❑ Use Permit ❑ Minor Use Permit ❑ Minor Variance ❑ Variance ❑ Administrative Permit ❑ Detached Building Use Form ❑ Encroachment Permit ❑ Aericultural Worker Affidavit ❑ Agricultural Acknowledgement Statement Zoning: F R — J C. Applicable Building Setbacks: ❑ Setbacks drawn on site Plan. ❑ CDF approval needed for encroachments into SRA setbacks. Pate 2 of 5 Zoning Code Streets & Highways Fire Prevention Subdivision Map Front aL Side © �� Side Street Rear ® �® Height rW—atenvav N/A N/A N/A ❑ Setbacks drawn on site Plan. ❑ CDF approval needed for encroachments into SRA setbacks. Pate 2 of 5 Applicable Development Fees: Standard Fees Amount Formula ❑ Fire ❑ School* ❑ Parks/Recreation ❑ Roads ❑ Sheriff ❑ Drainage - ❑ NCSP/CSA 87 ❑ Chico Urban Area — Road ❑ Thermalito Impact ❑ Other Subdivision.Map Special Fees ❑ Water Tender ❑ Road Improvement ❑ North Oroville Area ❑ Other (per map) * Check with school district to verify actual fee if pre -application review. A final determination will be made at the time of the building permit. Parcel Created By Q Deeds: ' Date of Creation: Legal Access Provided: ❑ No ❑ Yes Deed of Reference: Legal Access Required ❑ No ❑ Yes Parcel Frontage on Publicly Maintained Road: ❑ No ❑ Yes, Road Name: Complies with County Standards for Deed Creation: ❑ No ❑ Yes - Comments: ❑ Parcel Deemed to be legal ❑ Verify Legal Parcel ❑ Verify Legal Access ❑Provide Deed of Creation ❑ Obtain a Certificate of Compliance ❑ Comply with Old Subdivision Lot Ordinance (Maps recorded prior to Book 17 of Maps Page 23). ❑ Construct road to: ❑ Meet Parcel size required by zone ❑ Meet current Environmental Health Department requirements -------------- --- - ------ ------------------------------------------------------------------------------------------------------ Page 3 of 5 1 M Subdivision Mar) arcel Map: Map Date of Recording: Lot: -.7_30_,7�2 ❑ Use Permit/Minor Use Permit Permit Number: Book: to Date of Approval: ❑ Comply with the following Conditions of Approval: ❑ Meet the Fire Safe Regulations of Butte County and P.R.C. 4290 Page: 6 ❑ Automatic fire suppression sprinkler systems shall be installed *in accordance with the National Fire Protection Association Standard for installation of sprinkler systems in one and two family dwellings and mobile homes, NFPA Standard 13D, unless a pressurized community water system, with hydrants that meet the Fire Department specifications, serves the parcel. ❑ Wood stoves and fireplace inserts shall be EPA approved and designed to meet the emission requirements of the California Clean Air Act of 1988, as amended. ❑ Provide an erosion control plan for building and land disturbance on slopes steeper than 30%. The Erosion Control Plan must be prepared by a registered civil engineer or other qualified professional and be submitted to and approved by the Department of Public Works. ❑ A plan prepared by a certified arborist, botanist or landscape architect that shows the existing on-site mature trees, located in any area proposed for buildings and vehicular access, and provides for methods to protect the trees identified to be preserved, shall be provided to and approved by the Planning Division prior to the issuance of building permits and/or prior to grading or vegetation removal. The removal of mature trees shall be minimized, where possible. A mature tree shall be defined as a tree with a trunk measuring 4 inches in diameter, 4 feet from ground level. Mature trees removed shall be replaced on a 3 -to -1 ratio, utilizing existing oak tree stock. Each tree to be preserved shall be surrounded by a circular zone (minimum 40 -foot radius) identified by an orange fence during construction activities. No vegetation removal, soil disturbance, or other development activities shall occur within the fenced area. ❑ Measures shall be taken to control fugitive dust emissions from all driveway and other civil construction associated with residential development. Approved dust control measures are found in the fugitive dust control plan for the site approved by the Butte County Air Quality Management District, a copy of which can be obtained from the Butte County Department of Development Services, Building Division." ❑ Engineered foundations are required. ❑ Class A roofs are required. Pate 4 of 5 .f ------------- Summary of Specific Requirements:, This information provided in this summary is based on the application information and on the best available data at the time of review. C:1hly Oocuments`•Bailding Pcrmit Site Plan Reviewl.doc Pace 5 of 5 NOTICE TO ASSESSOR HCD 433(B) THIS FORM MUST BE COMPLEDTED BY THE OWNER OF A MANUFACTURED HOME MOBILEHOME OR COMMERCIAL COACH AND FORWARDED TO THE COUNTY ASSESSOR UPON COMPLETION OF THE INSTALLATION OF THE UNIT ON A FOUNDATION SYSTEM PURSUANT TO SECTION 18551, HEALTH AND SAFETY CODE ORIGINAL PURCHASE PRICE FOR: The Basic Unit $ a 3 Type of Exterior Wall Covering: (Metal, Wood, etc.) Optional Equipment & Upgrades $ Type of Roof Covering: Subtotal $ (Metal, Wood, Composition, etc.) Accessories & Accessory Structures $ Heating Type: orced Air ❑ Floor or Wall Other (Specify)A,.,� $ r / 70 Air Conditioning: ❑ YES [-NO Tons Evaporative Cooler: ❑ YES DINO Delivery & Installation $ Built-in Cooktop: ❑ YES E'10 p-� TOTAL SALES PRICE $ Ic 02 o d' Built -In Oven: ❑ YS Built-in Dishwasher: , IBJ YES U NO ❑ N Built-in Wet Bar: ❑ YES [TNO Refrigerator: 2 -YES ❑ NO DOES THE BASIC PRICE INCLUDE: Roof Omhaig(Eaves): [SES ❑ NO inches' The Towbar(s) ❑ YES En'NO Furniture Included: ❑ YES ❑-ab Value $ Tires & Wheels ❑ YES IZINO Wheelhubs & A)des ❑ YES E NO (LENGTH X WIDTH) Carport: ❑ YES BINO x LIST NUMBER OF ROOMS: Awning: ❑ YES ETNO x Porch: ElYES 11 r01 NO x Bedrooms -2 Dining Room _� Garage: ❑ YES L.1 NO x Storage Shed: El YES ErNO x Baths Family Room Skirting: ❑ YES C?WO LNEALFEET l Kitchen Utility Room Living Room Other Rooms ffe-U The sales price as shown does not include any amount for any in-place location. The Assessor's Parcel Number of the installation site is Qu " 72-0 - y 3 % ( Ignature) a � ya �.�s�%n.s-de✓ (Address) 0%1up ps.973 (Telephone) �`. COUNTY OF BUTTE — DEPARTMENT OF PUBLIC WORKS 7 County Center Drive — Oroville, California 95965 Telephone: 534-4541 APPLICATION AND PERMIT aut!A( ice representatives of the County of Butte to enter upon the above-mentioned property for inspection purposes. --Date nature erm,�te o gent ` Receipt No. 1PZ White-D.P.W. — Yellow -Assessor — Pink -Inspector — Goldenrod -Applicant This permit is hereby issued under the applicable provisions of the Butte County Code and/or resolutions to do work indicated S10above for which fees have been paid. O'0,0 DIRECTOR OF P BLIC WORKS By Date Jr-- Building permif expires BUILDING Owner r/me1— ' SO. FT. OCC. BUILDING VALUATION Mailing Address J Telephone No. Fireplace Contractor Total Valuation Mailing Address S Permit Fee PI an Checking Fee &/or Penalty Telephone No. Permit Fee Building Address l PLUMBING No. @ I FEE PERMIT FILING FEE _ $2.00 Each Trap 1.50 Repair drainage or vent piping 1.50 Water piping 1.50 Q Each gas water heater or vent 1.50 _ / A. P. No'.'. !p A -L Zani & e Gas piping system 1 - 5 outlets 1.50 S Each additional outlet 30 Fees w -G./ Sani ion FireDept. Fire Zone Use Permit Building sewer 5.00 EQA Parking Parcel Plans Declaration Parcel Ma 60' R/W Im rovements p Lawn sprinkler system 2.00 Bldg. Plans Recd Parcel Approvalpproval Permit Fee $ NEW ❑ ADDITION ❑ `UTILITIES OTHER ❑ ELECTRICAL No. @ FEE PERMIT FILING FEE $3.00 Main service incl. 1 meter Go Additional meters, each 1.00 Sub -panel (12 or less) (more than 12) Single Family ❑ Duplex ❑ Mobil Home Others ❑ Range, Cook -top or Oven 1.00 Water Heater or Space Heater 1.00 Light fixturesbal__�t?_c Receps., switches & fix outlets Z0�2b CONTRACTORS LICENSE LAW I am licensed under the provisions of Chapter 9, Div. 3, of the State of California Business & Professions Code under the name style of: Hood, Ex. FanorF.A. Furn. Motor 1.00 Evap. cooler, gar. di sp. or D.W. 1.00 Air conditioner or heat pump Water pump Mobil Home Facilities 5.00 Temp. Power Pole 5.00 License No. Classification Misc. wiring I am exempt from the Contractors License Laws of the State of California. Permit Fee G6 WORKMEN'S COMPENSATION INSURANCE 1 am aware of the provisions of Section3700 of the California Labor Code which requires every employer to be insured against liability for Workmen's Compensation. ❑I have placed on file with the County of Butte a certificate of Workmen's Compensation Insurance. I certify that in the performance of the work for.which this permit is issued I shall not employ any person in any manner so as to become subject to the Workmen's Compensation Laws of California. `"` 1 certify that I have read this application and state that the above information is correct. I agree to comply to all County Ordinances and State Laws relating to building construction, and hereby MECHANICAL No.1 @ I FEEPERMIT FILING FEE $3.00 Heating Cooling Ventilation Hood 2.00 Permit Fee $ TOTAL PERMIT FEE aut!A( ice representatives of the County of Butte to enter upon the above-mentioned property for inspection purposes. --Date nature erm,�te o gent ` Receipt No. 1PZ White-D.P.W. — Yellow -Assessor — Pink -Inspector — Goldenrod -Applicant This permit is hereby issued under the applicable provisions of the Butte County Code and/or resolutions to do work indicated S10above for which fees have been paid. O'0,0 DIRECTOR OF P BLIC WORKS By Date Jr-- Building permif expires A ` � -- COUNTY OF BUTTE — DEPARTMENT OFPUBLIC YVORKS ' / 7 CounryCon�rDnwo — Omvi||o. California .95965 " — Telephone: 534-454 APPLICATION AND PERMIT ". "."^"""� ". "°.= IL) V= uvvx mu 000vo�`onion eupmp,�yxxinupoununpu�ooeo ^ X Date Receipt No. z wh'^~o.px. — Yellow -Assessor — Pink -Inspector —n"/den~d.Appxcant This i is hereby issued under the applicable pro�.isions of the Butte County Code and/or resolutions to do wo� indicated a���,wmi���xa���mmu. ^ DIRECTOR OFPUBLIC WORKS By ~ ' '+ — Date BUILDING Owner SO. FT. OCC. BUILDING VALUATION Mai I ing Address Telephone No. Fireplace Contractor Total Valuation Mai I ing Address Permit Fee Building Address No. PLUMBING @ FEE PERMIT FILING FEE $2.00 Each Trap 1.50 Repair drainage or vent piping 1.50 'Water piping 1.50 Each gas water heater or vent 1.50 A. P. No. Zoning & Planning Gas piping system 1 - 5 outlets 1.50 Each additional outlet .30 Fees I W. C. San i taii on Fi re Dept. Fire Zone Use Permit Building sewer 5.00 Parking Parcel Lawn sprinkler system 2.00 Bldg. Plans Rec'd Parcel App roval Plans App rov a I Permit Fee $ NEW ADDITION UTILITIES OTHER PERMIT FILING FEE $3.00 Main service incl. 1 meter Additional meters, each 1.00 Sub -panel (12 or less) (morethan'12) - Single Family Duplex Mobil Home EJ Others 1:1 Range, Cook -top or Oven ' 1.00 Water Heater or Space. Heater 1.00 20 2y_ Light fixtures b; @ Receps., switches & fix outlets 1i oin - CONTRACTORS LICENSE LAW I am licensed under -the provisions of Chapter 9, Div. 3, of the State of California Business & Professions Code under the name style of: Hood,Ex. Fan or F. A. Furn. Motor 1.00 Evap. cooler, gar. disp. or D.W. 1.00 Air conditioner or heat pump Water pump Mobil Home Facilities 5.00 Temp. Power Pole 5.00 License No. Classification Misc. wiring M� I am exempt from the Contractors License Laws of the State of California. Permit Fee WORKMEN'S COMPENSATION INSURANCE 1 am aware of the provisions of Section3700 of the California Labor Code which requires every employer to be insured against liability for Workmen's Compensation. EJI have placed on file with the County of Butte a certificate of Workmen's Compensation Insurance. I certify that in the performance of the work for which this 'permit is issued I shall not employ any person in any manner so as to become subject to the Workmen's Compensation Laws of California. MECHANICAL No.1 @ FEE PERMIT FILING FEE J$3.00 Heating Cooling Ventilation Hood 2.00 Permit Fee $ $ I certify that I have read this application and state that the above 1 information is correct. I agree to comply to all County Ordinances and State Laws rel.ating to building construction, and hereby 0 TOTAL PERMIT FEE ]s ". "."^"""� ". "°.= IL) V= uvvx mu 000vo�`onion eupmp,�yxxinupoununpu�ooeo ^ X Date Receipt No. z wh'^~o.px. — Yellow -Assessor — Pink -Inspector —n"/den~d.Appxcant This i is hereby issued under the applicable pro�.isions of the Butte County Code and/or resolutions to do wo� indicated a���,wmi���xa���mmu. ^ DIRECTOR OFPUBLIC WORKS By ~ ' '+ — Date BUTTE COUNTY BUILDING DEPARTMENT APPROVED. All utility connections shall be located within 4 ft. outside the rear third section of the mobile home on the left (road) side of the mobile home. Septic system arl- u. be as per Butte County Health Dept. Re- quirements. The 4drig. Setback shall be 5 ft. froom the side property ;line •and 30, ft. from i the centerline, of the mad, permitting- a maximum of a 2 ft. eave overhang, t0"j i l ..40TE:—Ali Materials '& Workmanship "Shall Be in -n",. .�� Accordance with Recognized Good Practices ar'� e Zt< of a quality prescribed for the Specified use in t Uniform Building Code, Uniform Plumbing Code, aq the National Electrical CorIP Phis set of plans and specifications MUST be kept on the job at all times and it is unlawful 10 make any changes or alterations on same withovo Written permisson from the Department of pubrr Works, County of Butte. TO: Building Department FRO Environmental Health SUBJ Sanitation Clearance 9 os E.H. USE ONLY Plot Plan Attechod \ Floor Plan Attach®d— r ' Sana is B.a.&n rte_ Qn—� I r. &4 ts d , -;�; 4� - -�a --3 9 - Owner Location AP# Plan Approved for: Sew�.e'r Disposal )Water Sup ly: P blic Private Well Clearance for dwellind/1 f7IvY� )Q l a_ Hold final for: Final clearance O.K. for: NOTE: -- _- Environmental Healtfi Specialist 8/96 Aft FLEETWCOD. Woodland Park Series • Model 3403B 3 Bedrooms • 2 Baths • 940 Square Feet 4-_ \1 I M C > > ro 1 1 —01 a}E _ ml.. .. _«_ OPT. `� /. O I ❑❑ l_ _� � _ ... n - � � ..I I . OPT. OVAL SHOWER :. ! '. rL a...:._i._ ....c.. ;.....c.. .,_ ...;...TILITY. - .:...:. -ITCH N..:._ ::: _ _ BEDROOM .• i ! i ' IW . . IN , :.:.. • TH':::'.....;.wA •, LK-IN� i !To"X6. - - - -- CLOSET' r 23'-C," • W WALL� W/LEDGE _ MASTER LIVING ROOM e OPT. LINEN/ GUEST CLOSET OPr DEN. BEDROOM ti \ OPT.. \ INSWING \Opt DOOR ' - FIREPLACE ENTRANCE �p w. OPT• ANGLED RECE55EP ENTRY W V 17/MAY00 This appealing floorplan was designed with versatility that's hard to resist.Normally built with three standard -sized 4 bedrooms and two bathrooms, this beautiful -home can be E modified to feature two, s sized bedrooms and optional den.' ` The optional den allows you and your family to enjoy your,;, favorite television shows or other family activities: A spacious master bedroom walk-in wardrobe provides generous storage space for all,of your. clothing. Our over -sized living room window will allow you to f enjoy the breathtaking view - r from your borne site. STANDARD LIVING FEATURES Exterior Baths • Double cell porcelain sink adds • Fiber cement siding built to resist Easy -care laminate countertop flexibility in kitchen activities weather damage with hand laid, 4" ceramic tile backsplash provides attractive color accent Congoleum® no -wax, vinyl flooring • Full 3:12 roof pitch for exterior eye- for easy care appeal 2" x 4" exterior wall construction provides a sturdy frame Transverse floors with 2" x 6" floor joists for better support G.A.F. Class -"A' fire rated, composition shingle roof for long lasting performance • Vented roof cavity allows hot air and condensation to exhaust for improved energy efficiency • 36" inswing front entry door with deadbolt, peephole and brass knocker for your family's safety Interior • Decorative vinyl covered sheetrock wall panels that are easy to clean • Standard 17 oz. carpet in all living and bedroom areas for high performance and low maintenance - 100% nylon to prevent fuzzing and shedding - Multi -colored dye technique minimizes tracking and spotting - Treated with ScotchgardTM for easy cleaning • Blown acoustic ceiling throughout (vaulted in some areas) provides an open look and feel Recessed medicine cabinet provides convenient storage space in each bath Full-size 60" tub with shower head and surround for a relaxing bath or convenient shower Ceiling exhaust fan provides extra ventilation in each bath Window in each bath to provide natural light • MoenO single lever shower faucets -"Buy it for looks. Buy it for life" • Moen® 4" dual lever faucets -"Buy it for looks. Buy it for life" Kitchen • Maytag® appliances provide confidence and hassle -free service - 30" free standing gas range - 15 cubic foot frost -free refrigerator • Moen® single -lever metal faucet -"Buy it for looks. Buy it for life" • Bank of 4 drawers provides convenient storage for your utensils • Elegant crown molding provides a finishing touch to overhead cabinets Utility, Safety and Energy Features • Inside mount, 100 AMP panel box for easy access • 30 gallon electric water heater is efficient and requires low maintenance Intertherm gas furnace provides name brand confidence and hassle -free service Overhead utility shelf for added storage space Zone II insulation package for energy efficiency includes: white vinyl framed, dual -paned windows R-22 ceiling, R-11 wall, R-11 floor Shut-off valves at all plumbing fixtures for your convenience • Plumb/wire for washer and electric dryer provides convenient hook-up W V t 7/AUG00 -e,- 9vv Sai 3R\ PROVED tte Coun) Sig 59 Z -o COUNTY OF BUTTE - DEPARTMENT OF DEVELOPMENT SERVICES - BUILDING DIVISION 7 County Center Drive • Oroville, California 95965 • Telephone (530) 538-71;Al MIT NO. (Rev. 12/96) APPLICATION AND PERMIT ASSESSOR PARCEL NUMBER 098-790-039 ZON1N°i BUILDING PERMIT OWNER TELEPHONE SO. FT. OCC. BUILDING VALUATION - OWNERS MAIUNG ADDRESS 1970 NMzi_TFS11F ST FAHRUMP NV 99061 CONTRACTOR'S NAME TELEPHONE CONTRACTORS MAILING ADDRESS CONSTRUCTION LENDER Fireplace LENDER'S MAILING ADDRESS Total Valuation $ ARCHITECT OR ENGINEER LICENSE NO. Filing Fee $ 20.00 Permit Fee $ ARCHITECT OR ENGINEERS MAILING ADDRESS Plan Checking Fee $ BUILDINGADDRESS Bl(; BEND RD. CONGOW Energy Plan Checking Fee $ $ PERMIT FEE $ LOT NO. SUBDNISIOWS NAME PARCEL MAP PLUMBING PERMIT Fling Fee 20.00 Each Trap 7.00 USEOFSTRUCTURE SF ❑ Duplex ❑ Mobilehome ❑ Other SPECIFY Solar or heat pump water heater 23.00 Water piping 15.00 Each gas water heater or vent 15.00 TYPE OF WORK New ❑ Addition ❑ Remodel ❑ Utilities ❑ Installation ❑ Other ❑ Describe Work: p© p0TIR FO���T�, rte_ Gas piping system 1 - 5 outlets 15.00 Building sewer 15.00 Mobile Home S G W @20.00 PERMIT FEE $ ELECTRICAL PERMIT Fling Fee 20.00 Main Service ZDDAOR. 800V OR 23.00 93-00 LICENSED CONTRACTOR'S DECLARATION I hereby affirm under penalty of perjury that I am licensed under provisions of Chapter 9 (commencing with Section 7000) of Division 3 of the Business and Professions Code, and my license is in full force and effect.POWER License Class Lic. No. OWNER -BUILDER DECLARATION I hereby affirm under penalty of perjury that I am exempt from the Contractors License Law for the following reason: I, as owner of the property, or my employees with wages as their sole compensation, will do the work, and the structure is not intended or offered for sale. ❑ I, as owner of the property, am exclusively contracting with licensed contractors to construct the project. ❑ 1 am exempt under Sec. , Business and Professions Code for this reason Main Service zoOA TO lOooA 46.00 NEW CONST. DWELLING OCCUP. OR ADDNS. ( 8 ACC. S. S° 3.50FT. r,Dµp�IpT MULTI-OUTLETITS @7,50 APPARATUS b SINGLE OUTLET CIR. EX. Occup. OUTLET OR FDRURES .00 BAL Q I. 0 Ex. Occup. DFIx�LE�oSAF p OEA 5.00 Temporary Service 23.00 Mobile Home Facilities 20.00 Misc. Wirina 23.00 _ aza PERMIT FEE _ WORKERS' COMPENSATION DECLARATION 1 hereby affirm under penalty of perjury one of the following declarations: ❑ 1 have and will maintain a certificate of consent to self -insure for workers' compensation, as provided for by section 3700 of the Labor Code, for the performance of the work for which this permit is issued. ❑ 1 have and will maintain workers' compensation insurance, as required by Section 3700 of the Labor Code, for the performance of work for which this permit is issued. My workers' compensation insurance carrier and policy number are: Carrier MECHANICAL PERMIT Fling Fee 20.00 Heating Cooling Hood 6.50 Ventilation PERMIT FEE $ Policy Number (The above sections need not be completed if the permit is for work of a valuation of one hundred dollars ($100) or less.) I certify that in the performance of the work for which this permit is issued, I shall not employ any person in any manner so as to become subject to workers' compensation laws of California, and agree that 9 1 should become subject to the workers' compensation provisions of section 3700 of the Labor Code, I shall rthwith comply with those provisions. X Date �o� _ Signat . `of Applicant - Owner ❑ Contractor ❑ Agent An OSHA permit is required for excavations over 5'0" deep and demolition or construction of structures over 3 stories in hei ht. Mobile Home Installation Fee $ Energy Inspection Fee $ Occ CONST. TYPE it TOTAL FEE w HAZ. I D. FEES IMP I FLOOD CDF PARCEL PO HD ISSUE This permit is hereby issued under the applicable provisions of the Butte County Code and/or Resolutions to do work indicateo above for which fees have een paid. C� Da V CJ PERMIT EXPIRES ON D e Receipt No. � . D WHITE-D.D.S.--B. D. C AR SSSOR PINK -INSPECTOR GOLDENROD -APPLICANT COUNTY OF BUTTE - DEPARTMENT OF DEVELOPMENT SERVICES - BUILDING DIVISION 7 County Center Drive • Oroville, California 95965 • Telephone (530) 538-7541 /1"', PERMIT O. Rev.. 12/96) APPLICATION AND PERMIT ASSESSOR PARCEL NUME R DONSA BUILDINGPERMIT n 0 owNIER Ta 1D1E ^ 3 SO. FT. OCC. BUILDING VALUATION OWNER'S IAAAMNO AVOMS . B n_ n-*- r' CONTRACTOR'S NAME ITEl�N10N CONTRACTOR'S 4ALMNG ADDRESS CONSTRUCTION LENDER LENDER'S ►WING ADDRESS ARCHfTECT OR ENGINEER ARCHITECT OR ENGINEER'S KVJUNO ADDRESS SUI DING ADDRESS 4 LOT NO. I SU YMIDN9 NAPE USEOFSTRUCTURE SF ❑ Duplex O Mobilehome ❑ Other eFECiY TYPE OF WORK New ❑ Addition ❑ DRemodel ❑ U6Gties ❑ Installation ❑ Other Describe Work: P&UN 1 10&-6n� laiX- �-/Q Z4. Q 4 sttier: �F � o 4hcx- s cen�K�'�Cr Fire lace PERMIT FEE : Total Valuation is Filing Fee 20.00 Main Service Flin Fee $ 20.00 Permit Fee $ NEW CONST. OR ADDNS. Plan Checking Fee $ KEW CONST. N ON.R@IO. Energy Plan Checking Fee b 9 --'PERMIT FEE E ll PERMIT FEE _ 20.00 PLUMBING PERMIT Fling Fee 20.00 Each Trap 7.00 Solar or heat pump water heater 6.50 23.00 Water piping 15.00 Each gas water heater or vent 15.00 Gas piping system 1 - 5 outlets 15.00 Building sewer 15.00 Mobile Home IS I G I W §20.00 Ex. Occup. OUTLET OR FDnURE11 PERMIT FEE : ELECTRICAL PERMIT Filing Fee 20.00 Main Service Roo OORR LESS 23.00 Q3 -0 r Main Service 200A TO 1000A 48.00 NEW CONST. OR ADDNS. DWELLM OCCUP. i ACC. FIDS. 3.505 KEW CONST. N ON.R@IO. ( umfo-OUTLET M.. Y`N/�IOf`J ■1Q ) @7.50 Ex. Occup. OUTLET OR FDnURE11 eAL w Ex. Occup. o°REn 5.00 Temporary Service 23.00 Mobile Home Facilities 20.00 'sc. Wiring 23.00 9 --'PERMIT FEE _ ll MECHANICAL PERMIT Fling Fee 20.00 Heatin Cooling Hood 6.50 Mobile Home Installation Fee S Energy Inspection Fee S OCc ODNBT T.ME TOTAL FEE $ v NAL 10. FEES I UP I FLOOD I COP I PARCEL PO ND ISSUE This permit Is hereby issued under the applicable provisions of the Butte County Code and/or Resolutions to do work indicated above for which fees have been paid. By Data PERMIT EXPIRES ON r� ONER-BUILDER VERIFICATION W Anencion Property Owner: An "owner -builder" building permit has been applied for in your name and bearing your si�� Please "complete and return this information at your earliest opportunity to avoid rydeLpr in processing and issuing your building permit. No building permit will be issued until dds v rification is received. 1 I personally plan to provide the major labor and materials for construction of the proposed Gproperty improvement: YES' . NO O I HAVES HAVE NOTV sj` d an application for a building permit for the proposed ago L 3. I have contracted with the following person (firm) to provide the proposed etion: NA:riE: SS: CITY: / PHONE: CONTR.ACTOR'S LICENSE N . 4. 1747 plan to provide po •ons of this work, but I have hired the ollowing person to cootdinsai supervise, and provide the 'or work: NA�ti�: " ADDRESS: CITY: PHOT -E: COQ CTO ICENSE NO. 5. I will provide some of the work t I have contracted (hire a following persons to provide the work indicated: NAME ADDRESS PHONE E OF WORK SIGNED: PROPERTYOWNER: x SOCI_-I. SECURUY NUi✓ME 3-oa NOTE: This Owner -Builder Verification is required by Section 19831 and 19832 4VAW California Health and Safety Code. This verification must be eosyp&*W Avd returned to our office before we are permitted to issue the permit OVER OWNER BUILDER INFORMATION j Ler.- ?-oce^: C•.�-_. An applicarion for a building permit has been submitted in your name listing yourself as the builder of property improvements specified For your protection. you should be aware that as -owner-builder" you are the responsible patty of --cot oninch a permit. Building permits are not required to be signed by property owners unless they are personally perfottising Iii own work. If your work is being performed by someone other than yourself, you may protect yourself from ptilAle liability if that person applies for the proper permit in his or her name. Contractors are required by law to be licensed and bonded by the State of California and to have a business license from the city or county. They are also required by law to put their license number on all permits for which they apply. If you plan to do your own work, with the exception of various Hades that you plan to subcontract. you should be aware of the following information for your benefit and protection: ' ♦ If you employ or otherwise engage any persons other than your immediate family. and the worst (including materials and other costs) is S300 or more for the entire project, and such persons are not licensed as contractors or subcontractors, then you may be an employer. ♦ If you are an employer, you must register with the State and Federal Governments as an employer and you are subject to several obligations including'stare and federal income tax withholding, federal social security taxes, workers compensation insurance, disability insurance costs, and unemployment compensation contributions. ♦ There may be tinancial risks for you if you do not carry out these obligations, and these risks are especially serious with respect to worker's compensation insurance. ♦ For more scccit:c information about your obligations under Federal Law, contract the Internal Revenue Service (and, if you wish, tie U.S. Small Business Administration). For more specific information about your obligations under Stace Law, c --,-.:ac' the Department of Benefit Payments and the Division of Industrial Accidents. It the strucn:re is intended for sale, property owners who are not licensed contractors are allowed to perform their work personally or througlh their own employees, without a licensed contractor or subcontractor, only under limited conditions. A frequent practice of unlicensed persons professing to be contractors is to secure an "owner builder" building permit, erroneously implying that the property owner is providing his or her own labor and material personally. Building permits are not required to be signed by property owners unless they are performing their own work personally. Information about licensed contractors may be obtained by contracting the Contractors State License Board in your community or at 1020 N Street, Sacramento, CA. 95814. Please complete the "Owner Builder Verification" on the reverse side of this form so that we can confirm that you are aware of these matters. The building permit will not be issued until the verification is returned. IIN't rely. el C. Vi ira, C.B.O. ger, Building Inspection 11 1k, NOTE: Thar 0wnrr-8uilder Info rmadon is required by Section 19810 of the Calijornla Health and Safety Coda OVER REQUEST FORINSPECTION, Permit No. Location: A... _ _ f • Owner: Contractor: _ Comment: —: BLDG. PLUMB/MECH ELECTRIC M.H.I./M.H.0( PRE - INSPECTION Form Rough Rough Fnd/Ftg Frame/Underfloor Top Out Temp. Service Job Status Stucco Lath Gas Pipingrrest Main Service Corrections PermitBene at Stucco Brown Temp. Gas Underground Final Woodstove Sewer Piping Well Circuit Ex Mobile Site Brace Panel Water Piping POOL Insulation Shower Pan Nailing Gunite Demo Bonding Light Niche Corrections Corrections Corrections Final Final Final Corrections Final Ready for Inspec. on: Date: Call L) Phone: I 1 C� • PRE -INSPECTION REPORT OWNER LOCATION: CONTRACTOR: PRE-INSPETION FOR: 64Z�B_qzo -3 DATE: a A.P. #• ZONING: DATE TO INSPECTOR: y/ PERMrr MSTORY (ANONE ( ) AS FOLLOWS: BUILDING INSPEC'TOR'S RZPORT Building Description: Comma+cial/Usaga: ResidentiaLlf of Units: Currently Occupied Abandoned/Vacant Electric: Yes a No Electric curre:itly On Off Condition of Electric Gas: t Natural Propane None Currently On Off Obvious Problems: Sanitation: Plumbing Working Well Working Potable Water Obvious SewageProblems�� Comments: ,, Q az-4 ACTION RECOMMENDED: ISSUE: HOLDFOR Inspector. Date Sketch buildings on reverse and indicate location on p'ropert;- COUNTY OF BUTTE - DEPARTMENT OF DEVELOPMENT SERVICES - BUILDING DIVISION 7 County Center Drive • Oroville, California 95965 • Telephone (530) 538-7541 PERMIT NO. Rev. 12/96) APPLICATION AND PERMIT - ";)3 9 e-, �sessoR„wenNuu,e, n°�10 BUILDINGPERMIT owrlR�. L Ne SO. FT. OCC. BUILDING VALUATION i, 3 ONNIM'S uaurlG A9o '. ?0, COMPACTOR'S NAW I TOAIIIONJ,,A/ CONTRACTOR'S MAJU 1iG AOOAI1= CONSTRUCTION LENDER LENOWS NAILING AOORESS ARCHITECT OR ENGINEER ARCHrrECT OR ENOINEER7 wwtlG ADDRESS LOT NO. I SUSONSK N9 MARE USEOFSTRUCTURE SF ❑ Duplex ❑ Nlobilehome ❑ Other svEcsr TYPE OF WORK New ❑ Addition ❑ DRemodel ❑ Utilities O lista%lotion ❑ Other Describe Work: rOZ�^C/1 Y G/iY- ,L�� —a Total Valuation Fling Fee Permit Fee Plan Checking I Enerav Plan Ch i b b b Fee b b RMIT FEE t 20.00 PLUMBING PERMIT Fling Fee 20.00 Each Tr 7.00 Solar or heat pump water heater 23.00 Water piping 15.00 Each gas water heater or vent 15.00 Gas piping system 1 - 5 outlets 15.00 Building sewer 15.00 Mobile Home I S I G I W F 1 §20.00 0 PERMIT FEE f 11 MECHANICAL PERMIT Fling Fee 20.00 Heating —Cooling WMd 8.50 PERMIT FEE I S Mobile Home Installation Fee b Energy Inspection Fee = OCC CONST. TTMPe TOTAL FEE $VA NAz 0. ns NP RXIOD cor This permit is hereby issued under the applicable provisions of the Butte County Code and/or Resolutions to do work indicated above for which fees have been Paid. By Date PERMIT EXPIRES ON PERMIT FEE ! ELECTRICAL PERMIT Filing Fee 20.00 Main Service zooA oma LE�ss 23.00 -.0 Main Service 200A TO t— 46.00 NEW CONST. OR ADONS. Dvr9il+o OOCUP. i ACC. aDs. 3.5QSO NEW WNST. NON.RESID. rULTFOunEr §7.50 vowel AvaAruTts a SlIOLE OVRET p0. EX. OCCU oLJTLEr OR ForTLIREs m 0 1.00 SAL 0 .w Ex. Occup. ounE°TaESIo.A"UO°RE 5.00 Temporary Service 23.00 Mobile Home Facilities 20.00 Misc. Wiring 23.00 0 PERMIT FEE f 11 MECHANICAL PERMIT Fling Fee 20.00 Heating —Cooling WMd 8.50 PERMIT FEE I S Mobile Home Installation Fee b Energy Inspection Fee = OCC CONST. TTMPe TOTAL FEE $VA NAz 0. ns NP RXIOD cor This permit is hereby issued under the applicable provisions of the Butte County Code and/or Resolutions to do work indicated above for which fees have been Paid. By Date PERMIT EXPIRES ON ., • r.. . `S� � Z � s