HomeMy WebLinkAbout018-040-007CUSTOMER INFORMATION
CLIENT NAME
Joan Keesey
ADDRESS:
41 Falcon Pointe Dr
CITY:
Chico, CA 95928
PHONE:
310-850-0699
AHJ:
Butte County'
APN #
018-040-007
APPLICABLE CODES
C. w
• 2011 NATIONAL ELECTRICAL CODE (NEC) _
• 2013 CALIFORNIA ELECTRICAL CODE (CEC)
• 2013 CALIFORNIA BUIDLING CODE (CBC)
• 2012 INTERNATIONAL BUIDLING CODE (IBC)
SCOPE OF WORK
14.28kW Roof Mount with 51 SolarWorld SW 280 Mono Black modules and
SolarEdge inverters
w'
is
General Solar Specs s
• THE PV MODULES ARE CONSIDERED NON-COMBUSTIBLE AND THIS SYSTEM IS AN UTILITY INTERACTIVE SYSTEM WITH NO STORAGE BATTERIES..
• PER NEC, GROUNDING ELECTRODE SYSTEM OF EXISTING BUILDING MAY BE USED AND BONDED TO AT THE SERVICE ENTRANCE. IF EXISTING SYSTEM IS
INACCESSIBLE, OR INADEQUATE, OR IS ONLY METALLIC WATER PIPING, A SUPPLEMENTAL GROUNDING ELECTRODE WILL BE USED AT THE INVERTER
LOCATION CONSISTING OF A UL LISTED 8FT GROUND ROD WITH ACORN CLAMP. GROUNDING ELECTRODE CONDUCTORS SHALL BE NO LESS THAN #10 AWG'
AND NO GREATER THAN #6 AWG COPPER AND BONDED TO THE EXISTING GROUNDING ELECTRODE TO PROVIDE FOR A COMPLETE SYSTEM.
• EACH MODULE WILL BE GROUNDED USING AN INTEGRATING GROUND SYSTEM. ' {`
• EXPOSED NON-CURRENT CARRYING METAL PARTS OF MODULE FRAMES, EQUIPMENTS, AND CONDUCTOR ENCLOSURES SHALL BE GROUNDED IN �
ACCORDANCE WITH 250.134 OR 250.136(A) REGARDLESS OF VOLTAGE.
• PROPER ACCESS AND WORKING CLEARANCE AROUND EXISTING AND PROPOSED ELECTRICAL EQUIPMENT WILL BE PROVIDED AS PER SECTION 110.26 NEC.
• ALL PLAQUES AND SIGNAGE WILL BE INSTALLED AS REQUIRED BY 2011 NEC.
• HEIGHT OF INTEGRATED AC/DC DISCONNECT SHALL NOT EXCEED 6'-7" PER NEC 240.24
• THE GROUNDING ELECTRODE CONDUCTOR SHALL BE PROTECTED FROM PHYSICAL DAMAGE BETWEEN THE GROUNDING ELECTRODE AND THE PANEL (OR
INVERTER)IF SMALLER THAN #6 AWG COPPER WIRE PER NEC 250-64(B). THE GROUNDING ELECTRODE CONDUCTOR WILL BE CONTINUOUS, EXCEPT FOR
SPLICES OR JOINTS AT BUSBARS WITHIN LISTED EQUIPMENT PER NEC 250.649(C). +, r
W o
0
SYSTEM INFORMATION
SYSTEM SIZE:
14.28kW
PV MODULE:
SolarWorld SW 280 Mono Black
RACKING:
IronRidge
INVERTER(S):
t0. SolarEdge
AZIMUTH:
Multiple
TILT:
5/12
MODULE COUNT:
51
MOUNTING:
Roof Mount
ROOF:
Concrete Flat Tile
TYPE:
Truss
w'
is
General Solar Specs s
• THE PV MODULES ARE CONSIDERED NON-COMBUSTIBLE AND THIS SYSTEM IS AN UTILITY INTERACTIVE SYSTEM WITH NO STORAGE BATTERIES..
• PER NEC, GROUNDING ELECTRODE SYSTEM OF EXISTING BUILDING MAY BE USED AND BONDED TO AT THE SERVICE ENTRANCE. IF EXISTING SYSTEM IS
INACCESSIBLE, OR INADEQUATE, OR IS ONLY METALLIC WATER PIPING, A SUPPLEMENTAL GROUNDING ELECTRODE WILL BE USED AT THE INVERTER
LOCATION CONSISTING OF A UL LISTED 8FT GROUND ROD WITH ACORN CLAMP. GROUNDING ELECTRODE CONDUCTORS SHALL BE NO LESS THAN #10 AWG'
AND NO GREATER THAN #6 AWG COPPER AND BONDED TO THE EXISTING GROUNDING ELECTRODE TO PROVIDE FOR A COMPLETE SYSTEM.
• EACH MODULE WILL BE GROUNDED USING AN INTEGRATING GROUND SYSTEM. ' {`
• EXPOSED NON-CURRENT CARRYING METAL PARTS OF MODULE FRAMES, EQUIPMENTS, AND CONDUCTOR ENCLOSURES SHALL BE GROUNDED IN �
ACCORDANCE WITH 250.134 OR 250.136(A) REGARDLESS OF VOLTAGE.
• PROPER ACCESS AND WORKING CLEARANCE AROUND EXISTING AND PROPOSED ELECTRICAL EQUIPMENT WILL BE PROVIDED AS PER SECTION 110.26 NEC.
• ALL PLAQUES AND SIGNAGE WILL BE INSTALLED AS REQUIRED BY 2011 NEC.
• HEIGHT OF INTEGRATED AC/DC DISCONNECT SHALL NOT EXCEED 6'-7" PER NEC 240.24
• THE GROUNDING ELECTRODE CONDUCTOR SHALL BE PROTECTED FROM PHYSICAL DAMAGE BETWEEN THE GROUNDING ELECTRODE AND THE PANEL (OR
INVERTER)IF SMALLER THAN #6 AWG COPPER WIRE PER NEC 250-64(B). THE GROUNDING ELECTRODE CONDUCTOR WILL BE CONTINUOUS, EXCEPT FOR
SPLICES OR JOINTS AT BUSBARS WITHIN LISTED EQUIPMENT PER NEC 250.649(C). +, r
W o
0
a
L
o 00
r o
M
E
Z
V
U
0
0
0
t
a
U
Y
0
p`
N
0
> o �
y n at
O .0
Y m O
C LL V
° v u
6
a
• i
Cover Page
.. ...['� � �e .. r r,. F �j. \j � ��� .� F4- � '� �-�f Nom•. - ,
/ry AnrA
29'-78,'
` 5'-6„
I
26-43„
3'typ.---------..........._$-...------------�
r-
10'-11$"
f
32'-11$"
l
ATTACHMENTS NOT TO EXCEED 72"
L � �
32'-11$"
CD
00
'ROD M
m 5 N LO W
C
N x
Lu
%W LLh
C O m
�'n mVOU
Eu)U
to
a
g
0
CW
�W
(A
rn o
1 o
0
d a
L o
d °°
m
o
Z
CL �+
a
N
U
+J
0
0
O
t
G.
U
Y
00
p` N.
v ap
rn .
o Ln
ar a m
c
w o u
Y
C Li o
N u
� a U
E
1�
e
a
a
Project Plan
' .+f _ r - qtr - dy r , �j•`_• .. �.� � f. � } � �#{.. .ti `.+T, ,t�� .. -
•
• ''a ,! ' � r r . .. � e ,. i+ . t moi: -.
!f
r
cp
co
-
• -
C V% � n
000 U
t•0I
..
-. •
-
1r .
t. ,..
- F
ej N.
m
•
LJB
JB
PNL
cnW
cn
U3 9
O
op
00
t f
0
�.
0
0
00
co
s
14
0)Ln
..
u 0 U
PLAN LEGEND •
_
•Z
C i 0
l
' ❑i
DC/AC INVERTER
..
�
f.
'... • 4
'
° L
a u
PNL
Y
AC PANELBOARD-
- T „
•
Fs
AC DISCONNECT
DC DISCONNECT
,
O
(E) UTILITY METER
a
t,
0
PV REVENUE METER
Rcea
COMBINER BOX
Fal
JUNCTION BOX
w
}:
€
MAIN ELECTRICAL PANEL
'
•
_-
itLLU
EQUIP. GROUND
----
CONDUIT
{r
. ;
} r
*'
Plan
EElectrical
FIRE CLEARANCE
r'
180' True
„
-
SCALE: Custom - r> • ,
' .+f _ r - qtr - dy r , �j•`_• .. �.� � f. � } � �#{.. .ti `.+T, ,t�� .. -
•
• ''a ,! ' � r r . .. � e ,. i+ . t moi: -.
— -- i -- --;--
17 1
1+ +
�— ------------
17 -- -- ----
17IF1 11 11 1•
�—+ 11 it
—
-----------
i i
'17 •
1+ +
--------------------------
co
co
-------------------------
DERATING OF MAIN BREAKER
UTILITY SOURCE = 175A
a PV SOURCE = 60A
TOTAL OF SOURCES = 235A
RATING OF MAIN SERVICE = 200A
120% OF 200A = 240A
r `
CONNECT PV SYSTEM ON LOAD
i SIDE OF MAINS TO CIRCUIT
. BREAKER WITH DERATED MAIN
NFc F;qn ra
co
m
U co,
(V N 0
C V%XA
W
C 0 LL W
N m V O U
'E $ U) U
a
0
CW
�W
.ems
oP•
i
o
0
a a
LnO
op
ooa
E
z
a
a
aj
+,
�
N
U
M
O
O
O
L
a
U
0
00
o
N
oo
v aLn
o
`s v u
Y m O
c u
O C U
e
a
Single Line
Diagram
DESIGN TEMPERATURES
Circ. Name
Manufacturer
ASHRAE DATA
SolarEdge
Lowest Expected Temperature
SE1140OA-US
-3
-C
Average High Temperature
Nominal Output Voltage
41
"C
PV MODULE SPECIFICATIONS
1
Manufacturer
SolarWorld
Model #
SW 280 Mono Black
PMAX (Nominal Output)
280
W
VMP (Voltage at Pmax)
31.2
V
IMP ( Current at Pmax)
9.07
A
VOC (Open Circuit Voltage)
39.5
V
ISC (Short Circuit Current)
9,71
A
NOTC
25
°C
Temperature Coefficient of Pmax
-0.43
%/ °C
Temperature Coefficient of Voc
-0.0031
%/ °C
Temperature Coefficient of Isc
0,044
%/ °C
MAXIMUM SYSTEM VOLTAGE
1000
#10
INVERTER 1 SPECIFICATIONS
Circ. Name
Manufacturer
Voltage(V)
SolarEdge
Model#
SE1140OA-US
Nominal AC Power
11400
W
Nominal Output Voltage
240
VAC
Number of Phases
1
PH
Nominal Output Current
47.50
A
AC OCP Rating
60
A
Max. Array Input Voltage
500
VDC
MPPT Min at Full Power
350
VDC
MPPT Max at Full Power
350
VDC
2 Strings of 17 on MPPT1
34
Modules
1 Strings of 17 on MPPT2
17
Modules
VOLTS
CONDUCTOR AND CONDUIT SCHEDULE (COPPER)
ID#
Circ. Name
Circ.
Conductor
Voltage(V)
Load(A)
Ampacity for
OCP (A) (Load
x 1.25)
Tamb
Raceway
Conductor Required#
Ampacity (A)
Conductor Size &Type
of Runs
per Phase
Conductor
Ampacity
Copper
E.G.0
CONDUIT
Voltage(V)
Amperage(
A)
LENGTH
1 WAY
Voltage Drop
(%)
1
PV String
PV+/-
350
15.00
18.75
0.82
1.0
18.75
#10 PV Wire
1
35
#10
N/A
350.0
13.60
100 approx
0.97
2
PV -1
PV -1+/-
350.0 1
15.00
18.75
0.82
0.7
26.13
#10 THWN-2
1 135
#10
MC Cable
350.0
13.60
75 approx
0.72
3
INV i 1
L1,L2,N
240.0 1
47.50
59.38
0.82
1.0
59.38
#6 THWN-2
1
65
#8
ROMEX
240.0
47.50
75 approx
1.32
NOTES: STRINGS 1 AND 2 MUST BE COMBINED AT THE
INVERTER WITH 3 HOLE NSI CONNECTOR DUE
TO THE INVERTER
ONLY HAVING TWO INPUTS.
I
6
a
Bill Of
Materials
Descnpt*on.. _. �,, Pag Winber� Quantity
XR100, Rail 168" (14 Feet) Black XR-100-168B 30
Kit, 4pcs, Grounding Mid Clamp 2.25", Black RS-GD-MCL72258 23
4 -pack, End Clamp (C) 1.57", Black 29-7000-157B 5
Kit, 4pcs, Slotted L -Foot, Black, RS -LFT -0018 16
Kit, Splice XR100, Mill (1) XR-100-SPLC 20
Kit, 2pcs, Grounding Strap RS-GDST-001 5
Kit, 2pcs, Grounding Lug T -Bolt RS-GDLG-002 2.5
-Quick Mount Tile Hook 62
co
CP
Go
M
U
°T:�W �0,
m= N W
CU" � n
C Q N LL W
U, mVOU
j U)
N d
i3
�w
ZZ
rn o
0 4
6 c
0 0
d 00
o
m
Z
4J
CL
Q
N
N
U
0
O
O
t
a
U
00
o`
N
oo
rn
a>' a rn
ri
N C Q
CU o li
Y
O
C Li
M N L
° c v
I
6
a
Bill Of
Materials
}
CAUTION: SOLAR ELE TRIC
SYSTEM C®N
111:1914-4111*11,111641
1
■ ■ ,
mUllARNING4A
DUALMP.OWERISUP.P.0►Y
SOURCES: UTILITY'GRID'AND
PV SOLAR ELECTRIC SYSTEM
1 ■ ■ 1
NEC 690.14(2)
AC DISCONNECT
o DAO 'DD O`D :, •
SOLAR LOAD CENTER
NEC 705.12(7)
NEXT TO ALL SOLAR BREAKERS
SolarEdge SE11400A-US
IL_', 7 � I - " , I I I � - I � I I.. �
- . . . 1.� I -_
iminiq him
•Ogg
o
NEC 690.53
° , , ° ® .,�
All interior and exterior conduit, raceways, enclosures, and cable assemblies at turns
ob
above and/or below penetrations to be labeled every 10'. +
; `
°• • ° ° a.• =
Z
: r
;
IL_', 7 � I - " , I I I � - I � I I.. �
- . . . 1.� I -_
iminiq him
•Ogg
o
NEC 690.53
° , , ° ® .,�
op
ob
DC DISCONNECT / INVERTER
°• • ° ° a.• =
Z
: r
;
NEC 690.17(4)
:
MAIN SERVICE, SUB PAN EL(S), AC DISC.- `
D
M
O
Y
e • ..• .; ;r. ti -
0
-ki rej
LT5%RAM.
-
•
J.
J - !
♦
- t• ..;
M
W
-NEC 690.35 (F) .
; , _ Y ,%'
co j;t
LOCATED ON J -BOX / COMBINER BOX
�,��.�
aLn
cl
,.�
_
a
i
o
s
• S R•
t0
•
.
-`j.p;
`ref
'
4
C :.�,.
, _ `.,`.. .1
1A_
art .w
4. F
Placards
_
,
''. `
'.fyy, -
• � _ _�k•-} f -�;:" Mr ,., j,i
- 't t ter.
*..
_ •�
Yti
�.. .
':i .r a t i
'. • - . .. . _ °'t:4 �
+f
' , .- � C .,fir• � .. ,,,s . .s
�-y �.. ' ..
-
-
' • .
CD
Ob
T
E J N'n (OD {
4 L
Sunrnodule/`Pl u s i {: {. Sunmodule;
-/Plus u s .. t , N a
N
SSW;280 MONO.BL`ACK SW 280 MONO BLACK REALVALUE`
PERFORMANCE UNDER STANDARD TEST CONDITIONS (STC)' PERFORMANCE AT 800W/m2,NOCT,AMI.S
280 Wp
t* t,,,, y ,N,tuv. ' - T l Maximum ower Pm;; 207.2 W
tu oo Maximum power P,,,,, P - P . 1, Open + Open circuit voltage V� 39.5 V, Open circuit voltage V 35.8 V
TUV Power controlled:
_ 4 te Maximum PowerPoint voltage V„�
Lowest measuring tolerance in industry ] 31.2Vi Maxlmumpowerpofntvoltagey 28.3y Y y
• +` Short circuit current I„ 9,71 Short circuit current I„ - _ 7.85 A _ l7 •.s -
�- r0
- - Maximum ower oint current 1 Pc ' „ 7.33 A " • ` ' r - W
,i.. Moximumpawerpoin[currerrt I,,,W r.9.07A P P C.Z
Module efficiency n„ - - 16.7%� Minor reduction in efficiency under partial load conditions al 250C: at 200W/m2. 100% '.,r � W
(d-2%) of the STC efficiency (1000 w/m-) is achieved.
'STC:1000 W/m', 25•C, AM 1.5 • . v 1
I'! Every component is tested to meet 1) Measuring tolerance (P.J traceable to TUV Rheinland: 2% (TUV Power controlled). COMPONENT MATERIALS
• 3times IEC requirements
THERMAL CHARACTERISTICS Cells per module 60
` - •Y NOCT--"48,°C„ Cell type Mono crystalline i. �4 .�,: . t�, ��;• _
- • 7+ TC 1" i Cell dimensions 6.17 in x 6.17 in (156.75 x 156.75 min) s • Psy e.
r r - •044 % 'C / Front Tempered glass (EN 12150) �Y*-
10 / Y 2,
- Designed to withstand heavy _ - TC.,„•. '�" ' 0:31 %/°C�-� Frame - Black anodized aluminum ! `
t TC P,„,„ l f -0.43 %/°C
accumulations of snow and ice - ' weight 39.5 lbs (17.9 kg) k' ` rn n
• •` J Operating temperature' -40'C to.85•C - ,+ y. 0) o
i C)
~ SYSTEM INTEGRATION PARAMETERS a- - - 6 o
{ _.l� ° • Is< 4:'_ 1000 W/ms Maximum system voltage SC 11/NEC 1000 V,. .� - d 00 '
O
o
SunmodulePlus: ■ Maximum reverse current 25A s m
• .. - Positive performance tolerance �-800 W/ms � Z
Numbero yposs diodes 3
CL
Q
113 psf downward
600 W ms . Design (Wads' Two rail system C a Ln
' •' .d' • / 64 psf upward:.,,. .= T. ; =.
170 psf downward 6-
Design Design Loads• Three rail system
` a F 400 W/m° 71 psf upward
25 -year linear performance warranty t - 30 psf downward y 4
Design Loads' Edgemounting '}'
Z ` and 10 -year product warranty v 200 W/mr - 30 psf upward - _ • O
- - 100 W/m° 'Please refer to the Sunmodule installation instructions for the details associated with
- these load cases.
r
O
MRe Ie JotngeiVJ V. ADDITIONAL DATA { ^'�
.` Glass with anti -reflective coating {F=• - + 3 g p+
/ '
Powersortin ' -0 W 5 Wp ��, Q
d 1x 37.44(951) J -Box IP65.
= r "4r
_ - Module leads PV wire pe
Module type(U17703) r UL4103 with H4 connectors - _
• ` . w , .. - .1 r , r ♦s' `_
11.33 (288) Class Low iron tempered with ARC ! .a 00
r,
World-dass quality
.� Fully -automated production lines and seamless monitoringofthe process and mate- N
{4
rial ensure the quality that the company sets as its benchmarkfor its sitesworldwide. °:nr ; { w - > o Ln r-1
• ,T 153 as a m ,
39.37 (7000) 0.6 + �• R '�'
SolarWorld Plus -Sorting �� N ms m GO ® VERSION 2.5 FRAME° -Compatible with both "Top-Down"ioPlus-Sorting guarantees highest system efficiency. SolarWorld only delivers modules cus Version l : no
`_/ 2.Sfiame and°Bottom- mounting methods t s c v u
that have greater than or equal to the nameplate rated power. UL 1703 65.94 (1675) bottom jGrounding Locations: ? , . A Y
• 4corners oft•heframe
mounting
S
• holes •a locations along the len
thofthe2S ear linear performance uarantee and extension of product warranty to 10 year •I.
- J ♦ � P-0
SolarWorld guarantees a maximunT performance digression of0.7% p.a. inthecourse D' • module in the extended flange*• ,
'
of 25 years, a significant added value compared to the two-phase warranties com-
mon
om mon in the industry. In addition, SolarWorld is offering a product warranty, which has
been extended to 10 years Home Innovation
ecu cxvsR crnuiEo_ i• i•. ,
'in accordance with the applicable SolarWorld Limited Warranty at purchase. - - _ - - + - •r
www.solamorld.com/warranty 6 x4 t. "4. �z 4.20(107)t a r
• -1.22137) yFy}y A_`71 39.41(1001) ' �... ;( J •
' MADE IN USA OF US �,. y R ' { . , „' + . •^ , - '" j.'i, i
$OIarWOrld.GOm AND IMPORTED PARTS • y f
/ All units proddetl are imperial. Sl units provided in parentheses. �,
• ♦7 - - t SolarWorld AG reserves the right to make specification changes without notice. ' tSW-01-6026US 12-2014. 1.' •- ' d 7 r 'Module
Datasheet
2_1
F k,.* . t. n s •' y � � Y • � t ` i r . r ! i 5 � - • , • Y, � � `. • , • r7,' r,•, ` f ,.,�Tr ti •
s " • «,. C a n i • �• { f•� h. � �S'Y i A � �.• �f`. �•t ,
r t J ♦ 41,{[ :3 " oma
e T . i � - - _ .. � L. '; _ - � `' sA � � .'l'�r i; ,t,.. s • rr_.
P Single Phase Inverters for North America
=@@
- solar , • ! SE3000A-US / SE380OA-US / SE5000A-US / SE6000A-USsolar ; ,}
SE7600A-US/SEt0000A-US/SEI 1400A -US
- - _ - SE3000A•US SE3806A-US SESOOOA-US SE6000A•US SE760OA•US SE100DOA-U5-SE1140°A-Us_,>' t
(OUTPUT )
SolarEdge Single Phase Inverters - . . 9980 208V c---3
. - Nominal AC Power Output 3000 3800 .5000 6000 7600 11400 VA
....... ....... .......... ...... ....... ......... ...... ...... 10000 240V
5400 @ 208V • - • • j • 10800 @ 208V
For North -America Max. AC Power Output 3300 4150 6000 8350 12000 VA
I. ...... L..:..........1.545o�z4Qv• I.. I ...�.. I..........
• .. io9so @z4oy, ,
_ AC Output Voltage Min: Nom: Max!" _ _ _ 1
,3-u
3-Vac.........I.......✓.......I..............I.............,i.......✓......`. .................(.......... -
SE3000A-US / SE380OA-US / SE5000A=US / SE6000A-US / Output •• � a ••-'................................ *•_ +
AC Output Voltage Min: Nom: Max!'I _
211- 240 - 264 Vac ..
SE760OA-US / SE1000OA-US / SE1140OA-US
.ACfretluencYMin:Nom: Max iii•.•...I......•••.•• •••....•.••......... country setting•57,.60,-60:5).-•.•.••••.: •.•..............I...Hz._..
Max. Continuous Output Current 12.5 16 24 208V I 25 32 I 48 @@C47 5� I A • , y -* ,
.... ....... .......... .....21, 240V.. .. ... ............ ...42 .240V .......... ..... -
.GFDIThreshold• "w ..1.. .•.A. +•.' , .
i`
�:. 1 ...
Utility Monitoring Islanding Protection, Country Configurable Thresholds Yes i I Yes .0 .
`.) b (INPUT . I
t ,
��wert� - Maximuer(STC) -,,. •,.4050..,._ -.•••5100••• .-.6750....- ...--8100•.,. .•..10250-•,• ..•..135°0-„• - 6535°.: W--- •.,-* �_
Transfgrmer•less,Ungroun.ded ................................................Y.e.s
....................
................................................. I ....
Max. Input Voltage .................. I ............. ......................... S00 ...... ................. ( Vdc '. a •• r' t,
s t
Max: ........ .... ..... ..... ..... ........
s, •• i' r u` " °i NJa tdy ` .Nom..DC Input Voltage ..:............ L ............. 325 @.208V / 35° @ 240V....... (...Vdc:..
- -•+^-'•^r "*' �� ` • - • . 16.5 @ 208V33 @ 208V -
_ a Y��`-B7z8• V Max. Input Currend' x 9.5 13 18 23 �34 5' Adc ;,
I •, L � V.I.. I.. _ �..........._�. I M1
4
5.5 240 30.5 240V
,,o„,,,,,;,,,,:,. Max. Input Short Circuit Current..... ( ........ .. .45 ... ...... .. .... I A_dc } e
>,
... ...... I .............. ... .. .......... ..... .... .. .......... .......... ..
r - - • Reverse Polanty Protection Yes rl -
..i ....... ...... • ............. ................. ............... I... -
^,,,,,.. Ground•FaultlsolationDetection•.. _ •• 600kuSensitivity - r '
.. ............... ............... ....... .. ....... .. ........ ..... .. .. ... ... ... ... .. ... .. - .
G...
MaximuminverterEfficiency.• ., I 97.7�� .I.. •98.2 I 98.3 .I.. ��98.3�� .I.. --98.� ••98.. ..I. 0981•-�'-�%•.�
s.
v
8
9.5 ( ..9.........I..975'20.8..V..I97.5 I97.5 9977 5 20480V
:I.. �97 5'CEC Weighted Efficiency 9 ........ ............... .............. ...2..Y..
<Nighttime Power ConsumptionL<4 i • •. :% ..t`+ -• . f - •
2.5
tADDITIONAL FEATURES - ;. •' .. ;3 ,
Supported Communication Interfaces RS485t RS232, Ethernet, ZigB.ee (optional) ,
. s ., ................... ........ -
........ ............ .........
Revenue Grade Data ANSI C12.1 Oprionalu'
......................... .............I.. .......................... ............ ....... ....... I
Rapid Shutdown -NEC 2014 690.12 Functionality enabled when SolarEd a 2pid shutdown kit is installed)°)
I STANDARD COMPLIANCE.: 1
r
Saf t 74 U 199 C A 22.
r e ULi 1 UL1699B L 8 5 2
n
Grid Connection Standards •,I IEEE1547 •••.•.,• -
j' L
f J .. tr>3�Yr`brctyP u T Emissions........ ....... ............. .............. ... ..... FCC partly class 8........ ................. ........ ..
INSTALLATIONSPECIFICATIONS y
3 j ;, - AC output conduit size,/ AWG ren e I 3/4" minimum / 16.6 AWG ,� 3/4 minimum / 8 3 AWG J t i e
u e of strings... ...... ........ .................. ............... ........... ..
DC input conduit size / # / -3/4" mtmmum / 1-2 strings /
3/4" minimum / 1-2 strings / 16-6 AWG
+ ! AWG range„•,,, 14-6AVJG-� L
.......... .....v .............................. ............................... ............... .............. i . .. .. .../...
,
Dimensions with Safety Switch 30.5 x 12.5 x 10.5 / m
30.5x12.5x7.2/775x315x184 i -
... I ......................... ............... ..... ..... .............. ....... 775 x 315 x,260 . (•-
_,,,,,� �11tt • r Weight withSaferySwitch-••--- •-• 51.2/23.2 54.7/24.7'88.4%401-�' I-Ib/kg
convection i
Cooling E Natural Convection and internal i (Fans (user replaceable) +
'F.y r� 4i t.�ti fan (user
_ a +.. '?r:=;; ,,� c '',.,..j� a .,r„:✓«`' •„a �t "',d.s «.f'w re laceable '
The best cholcelfor SolarEdge enabled systems r . _ . - �................................... p........). ....
....
•f..':_-.,va,+ '+s. c-, +; .z�:... - •�., _ ._--..�. '.;1. Noise ..L..... <25 ............ ...............I............... ....1<50�.�' ........ ..L.•d8A -
Integrated arc fault protection (Type 1) for NEC 2011690.11 compliance; ii * s Min. -Max. Operating Temperature I sl
�' - - ,r ,.,, a •., ".,e• r < 13 to +140/ -25 to +60 (-40 to +60 version available ) 'F /'C e 1
,.:SU error efficiency 98%) '.. ..may , -.. .: „- - ` < f' a i" ,'r Rant;?........... f-... I
. r .. ......... ............... ..
P tY.I Protection Rating:... NEMA 3R -
Hol .t
5 m II'li htwei ht and eas to install n provided .. .. ................
a , g: g y s o p o Ided bracket ., ,, �� , ,,., .v A .,r: ': y.f ±q, ✓ ui For other regional setdngs Please contact SolarEdge support.
S.j;`•4'* �.• .s, .. -..is r.. •_... ,,i, -tie S� ,_.,' + t•�, ,•_sl l'? t• m A higher current wurre may be wed; the in -ter w -ill limit its input current to the values swted.
u
Built -In module -level momtonng F x,.,i Reenue grade imerte,PIN:SE-A-USDWNNR2(or 7600W imerter:SE7600A-U5002NNR21.
_ - - - - • .. V '' Ia: Rapid shutdown kit P/N: SE1000-RO-51.
Internet connection through' Ethernet or Wireless: -.,. ;,: i 1�•40wnlon P/N:SEwuA.USOWNNU4t1or76WWlnerter.SE7600A•US002NNW).
Outdoor and indoor ,installation
aFixed voltage inverter, DC/AC conversion only - - r`• y ,:
;lip;, x
Pre -assembled Safety Switch for faster installation a
Optional - revenue grade data; ANSI C12.1 e '
USA- GERMANY -ITALY-FRANCE -JAPAN - CHINA - AUSTRALIA - THE NETHERLANDS- ISRAEL www.solaredge.us
ob
m
U
5=
NN In
Wm CNN m
C M n
CO {p�N
N m U o U
C u, U U
M
0 f�
Cw
W
W
cn
on o
o
O
00 00
6
O
m
.. -
..
-
a
K
Q
A
P Single Phase Inverters for North America
=@@
- solar , • ! SE3000A-US / SE380OA-US / SE5000A-US / SE6000A-USsolar ; ,}
SE7600A-US/SEt0000A-US/SEI 1400A -US
- - _ - SE3000A•US SE3806A-US SESOOOA-US SE6000A•US SE760OA•US SE100DOA-U5-SE1140°A-Us_,>' t
(OUTPUT )
SolarEdge Single Phase Inverters - . . 9980 208V c---3
. - Nominal AC Power Output 3000 3800 .5000 6000 7600 11400 VA
....... ....... .......... ...... ....... ......... ...... ...... 10000 240V
5400 @ 208V • - • • j • 10800 @ 208V
For North -America Max. AC Power Output 3300 4150 6000 8350 12000 VA
I. ...... L..:..........1.545o�z4Qv• I.. I ...�.. I..........
• .. io9so @z4oy, ,
_ AC Output Voltage Min: Nom: Max!" _ _ _ 1
,3-u
3-Vac.........I.......✓.......I..............I.............,i.......✓......`. .................(.......... -
SE3000A-US / SE380OA-US / SE5000A=US / SE6000A-US / Output •• � a ••-'................................ *•_ +
AC Output Voltage Min: Nom: Max!'I _
211- 240 - 264 Vac ..
SE760OA-US / SE1000OA-US / SE1140OA-US
.ACfretluencYMin:Nom: Max iii•.•...I......•••.•• •••....•.••......... country setting•57,.60,-60:5).-•.•.••••.: •.•..............I...Hz._..
Max. Continuous Output Current 12.5 16 24 208V I 25 32 I 48 @@C47 5� I A • , y -* ,
.... ....... .......... .....21, 240V.. .. ... ............ ...42 .240V .......... ..... -
.GFDIThreshold• "w ..1.. .•.A. +•.' , .
i`
�:. 1 ...
Utility Monitoring Islanding Protection, Country Configurable Thresholds Yes i I Yes .0 .
`.) b (INPUT . I
t ,
��wert� - Maximuer(STC) -,,. •,.4050..,._ -.•••5100••• .-.6750....- ...--8100•.,. .•..10250-•,• ..•..135°0-„• - 6535°.: W--- •.,-* �_
Transfgrmer•less,Ungroun.ded ................................................Y.e.s
....................
................................................. I ....
Max. Input Voltage .................. I ............. ......................... S00 ...... ................. ( Vdc '. a •• r' t,
s t
Max: ........ .... ..... ..... ..... ........
s, •• i' r u` " °i NJa tdy ` .Nom..DC Input Voltage ..:............ L ............. 325 @.208V / 35° @ 240V....... (...Vdc:..
- -•+^-'•^r "*' �� ` • - • . 16.5 @ 208V33 @ 208V -
_ a Y��`-B7z8• V Max. Input Currend' x 9.5 13 18 23 �34 5' Adc ;,
I •, L � V.I.. I.. _ �..........._�. I M1
4
5.5 240 30.5 240V
,,o„,,,,,;,,,,:,. Max. Input Short Circuit Current..... ( ........ .. .45 ... ...... .. .... I A_dc } e
>,
... ...... I .............. ... .. .......... ..... .... .. .......... .......... ..
r - - • Reverse Polanty Protection Yes rl -
..i ....... ...... • ............. ................. ............... I... -
^,,,,,.. Ground•FaultlsolationDetection•.. _ •• 600kuSensitivity - r '
.. ............... ............... ....... .. ....... .. ........ ..... .. .. ... ... ... ... .. ... .. - .
G...
MaximuminverterEfficiency.• ., I 97.7�� .I.. •98.2 I 98.3 .I.. ��98.3�� .I.. --98.� ••98.. ..I. 0981•-�'-�%•.�
s.
v
8
9.5 ( ..9.........I..975'20.8..V..I97.5 I97.5 9977 5 20480V
:I.. �97 5'CEC Weighted Efficiency 9 ........ ............... .............. ...2..Y..
<Nighttime Power ConsumptionL<4 i • •. :% ..t`+ -• . f - •
2.5
tADDITIONAL FEATURES - ;. •' .. ;3 ,
Supported Communication Interfaces RS485t RS232, Ethernet, ZigB.ee (optional) ,
. s ., ................... ........ -
........ ............ .........
Revenue Grade Data ANSI C12.1 Oprionalu'
......................... .............I.. .......................... ............ ....... ....... I
Rapid Shutdown -NEC 2014 690.12 Functionality enabled when SolarEd a 2pid shutdown kit is installed)°)
I STANDARD COMPLIANCE.: 1
r
Saf t 74 U 199 C A 22.
r e ULi 1 UL1699B L 8 5 2
n
Grid Connection Standards •,I IEEE1547 •••.•.,• -
j' L
f J .. tr>3�Yr`brctyP u T Emissions........ ....... ............. .............. ... ..... FCC partly class 8........ ................. ........ ..
INSTALLATIONSPECIFICATIONS y
3 j ;, - AC output conduit size,/ AWG ren e I 3/4" minimum / 16.6 AWG ,� 3/4 minimum / 8 3 AWG J t i e
u e of strings... ...... ........ .................. ............... ........... ..
DC input conduit size / # / -3/4" mtmmum / 1-2 strings /
3/4" minimum / 1-2 strings / 16-6 AWG
+ ! AWG range„•,,, 14-6AVJG-� L
.......... .....v .............................. ............................... ............... .............. i . .. .. .../...
,
Dimensions with Safety Switch 30.5 x 12.5 x 10.5 / m
30.5x12.5x7.2/775x315x184 i -
... I ......................... ............... ..... ..... .............. ....... 775 x 315 x,260 . (•-
_,,,,,� �11tt • r Weight withSaferySwitch-••--- •-• 51.2/23.2 54.7/24.7'88.4%401-�' I-Ib/kg
convection i
Cooling E Natural Convection and internal i (Fans (user replaceable) +
'F.y r� 4i t.�ti fan (user
_ a +.. '?r:=;; ,,� c '',.,..j� a .,r„:✓«`' •„a �t "',d.s «.f'w re laceable '
The best cholcelfor SolarEdge enabled systems r . _ . - �................................... p........). ....
....
•f..':_-.,va,+ '+s. c-, +; .z�:... - •�., _ ._--..�. '.;1. Noise ..L..... <25 ............ ...............I............... ....1<50�.�' ........ ..L.•d8A -
Integrated arc fault protection (Type 1) for NEC 2011690.11 compliance; ii * s Min. -Max. Operating Temperature I sl
�' - - ,r ,.,, a •., ".,e• r < 13 to +140/ -25 to +60 (-40 to +60 version available ) 'F /'C e 1
,.:SU error efficiency 98%) '.. ..may , -.. .: „- - ` < f' a i" ,'r Rant;?........... f-... I
. r .. ......... ............... ..
P tY.I Protection Rating:... NEMA 3R -
Hol .t
5 m II'li htwei ht and eas to install n provided .. .. ................
a , g: g y s o p o Ided bracket ., ,, �� , ,,., .v A .,r: ': y.f ±q, ✓ ui For other regional setdngs Please contact SolarEdge support.
S.j;`•4'* �.• .s, .. -..is r.. •_... ,,i, -tie S� ,_.,' + t•�, ,•_sl l'? t• m A higher current wurre may be wed; the in -ter w -ill limit its input current to the values swted.
u
Built -In module -level momtonng F x,.,i Reenue grade imerte,PIN:SE-A-USDWNNR2(or 7600W imerter:SE7600A-U5002NNR21.
_ - - - - • .. V '' Ia: Rapid shutdown kit P/N: SE1000-RO-51.
Internet connection through' Ethernet or Wireless: -.,. ;,: i 1�•40wnlon P/N:SEwuA.USOWNNU4t1or76WWlnerter.SE7600A•US002NNW).
Outdoor and indoor ,installation
aFixed voltage inverter, DC/AC conversion only - - r`• y ,:
;lip;, x
Pre -assembled Safety Switch for faster installation a
Optional - revenue grade data; ANSI C12.1 e '
USA- GERMANY -ITALY-FRANCE -JAPAN - CHINA - AUSTRALIA - THE NETHERLANDS- ISRAEL www.solaredge.us
ob
m
U
5=
NN In
Wm CNN m
C M n
CO {p�N
N m U o U
C u, U U
M
0 f�
Cw
W
W
cn
on o
o
O
00 00
6
O
m
C
C
Z
d
a
Q
A
-
U
O
O
,O
CL
t
.,
•
20
Y
00
p`
N'
: m
o to
w a m
cu c Q
ro u U
Y m O
c
ro �- t
� a u
a
t
r
Inverter
Datasheet
25°r6 more energyModule-level
RoHS
Yes
cl)o
9 O
-
:
)INSTALLATION SPECIFICATIONS
0 0
rn
°
•
e
-
- Mawmum w -. "'"#
. Allo..... ed ..System...............Voitage..... .... ..... ........ ........ .. ..... ..... 1000 Vdc .. ......... .. .... ..
Dimensions including mounting bracket (W x L x H) I 141 x256 x 40.5 / 5.55 x 10.08 x 1.59 mm / in
-.. I
a
a»
.................................................... '. ..1
Dimensions excluding mounting bracket (W x L x H)
.........................................................................
F
.... .....
1 mm /in
, .
(
" °
WeiPt.(inclucling cables and mounting bracket
1170 / 2.54 -'-"
k Ib
_
-
a r '?
:'"
Input Connector
' EMC4 / Amphenol / Tycol
4�
.
y
`
=@@ �: • ,
'.
Output Connector
_ _SolarEdge Power Optimizer - Zep Compatiblesolar
, ,
solar '
UU
"•
..
P ............ ............ ..........I.. ..................
Output Wire Length
. Module Add -On For North America P300-ZEP
_ ... ..
m / ft
-
/
.......... ............................ ........... .. ......
Operating Temperature Range
t
'C %'F
�.
.^.
.'-
................................. ..........................:
Protection Rating
................... .......... ........
..
ch
N a rn
y c Q
v o U
SolarEdge Power Optimizer
Relative Humidity0
.............................................................
100
..............................................
4"
-.
-W
.
t�I Hated STC power of themodule. Module of up to 45% power tolerance allowed..
.............
' �'"`". ' • "-P.300-ZEP(for60-cell-PY modules)'
Zep Compatible""" Module Add -On
'R"ed poweri')
I
~
4300 [
Optimizer '
Datasheet
nputD
............... ............. ?
W.
s
�, R4', n' �,', r ? r• r
' ` THREE PHASE THREE PHASE
PV SYSTEM DESIGN USING A SOLAREDGE INVERTER `SINGLE PHASE
.. ....... .........I ....... .
Absolute Maximum Input Voltage (Voc at lowest temperature) j 548
..............................................
I Vdc
For North America P300-ZEP ��
.........................................................................
MPP
.... porting
.... Operating ................ 8..48 . r• ........I...
Vdc.....
Minimum String Length
g gt ( Optimizers)
I 8 10 18
Maxlmum Short Circuit Current (Isc) - (10 1 -
......................................................................
Adc
. - i e.. f i'. } r x. •. `T .i .Y 1,
r_. s• ♦ .alb.. s. r- �` . s.. Y V..,,. r• r -.��� ; .7 _ f
r "S q S- =' S -' ,:' i t L _ f. -
y
. Compatlbie.wlth Zep Groove.framed modules
..... ....... .................................. ...
Maximum String Length (Power Optimizers)
.... .......................................
.. ... .. ...................... ........... .......
.'.... 2511 25 5..
.......... ... ...................... ......................
...... ....
.......
Maximum DC Input Current 12.5
...... ....... P ....
...................................
Adc
... ,.
Maximum Power per String
15250 ] 6000 I 12750
W
i..............................I.... ................. ..........I.....%.....
Mx ncY
`
'—.Certified Zep Compatible"". bracket ; '•= yMitigates all types of module mamatch losses, from • '•,x=
Parallel Strings of Different Lengths or Orientations
t =
..
..............................99.5\.
Weight 8
ed Effi.. envy .................................................. .... S98 ..................................
. I :...
I., ..
...........
s_
manufaetu erance shading,
Attaches to'module frame without screws reduces on -roof ring tol to partial ding
t
.y....
""'
-
Overvoltage Category i .II'
t` labor and mounting costs-`.Flexible'system design for maximum space utilizafion, '' '`
c _ .
- "
OUTPUT DURING OPERATION (POWER OPTIMIZER CONNECTED TO OPERATING INVERTER)
Power optimizer equipment grounded through the bracket - Next generation: maintenance with module -level monitoring
Maxlmum Output Current ......................................... {15 `1 ............................... Adc....
.
�..
Maximum Output Voltage 60 5..
Vdc
-
}OUTPUT.DURINGSTANDBY:(POWER OPTIMIZER DISCONNECTED FROM INVERTER OR INVERTER OFF) v '
Safety Output Voltage per Power Optimizer _ 1 .
Vdc
_----.-.
tSTANDARDLOMFLIANCE �}'..
-
}�R} ....
_ '• •-..
�.t�,-.. •.
EMC t Y. FCC Part15-Class B, 1EC61000-6-2, IEC61000-6-3
Safety ) i ..........• ...IEC62109-1 (class II safety); UL1741
......................................................... .. ................... ............
L
,' `:
^ "
25°r6 more energyModule-level
RoHS
Yes
cl)o
9 O
-
:
)INSTALLATION SPECIFICATIONS
0 0
rn
o
=
e
-
- Mawmum w -. "'"#
. Allo..... ed ..System...............Voitage..... .... ..... ........ ........ .. ..... ..... 1000 Vdc .. ......... .. .... ..
Dimensions including mounting bracket (W x L x H) I 141 x256 x 40.5 / 5.55 x 10.08 x 1.59 mm / in
-.. I
4.
r, GE'
.................................................... '. ..1
Dimensions excluding mounting bracket (W x L x H)
.........................................................................
.................:..... _. .............
1 1141 x 212 x 40.5 / 5.55 z 8.34 x 1.59
.................................. ............. .....................
.... .....
1 mm /in
, .
(
" °
WeiPt.(inclucling cables and mounting bracket
1170 / 2.54 -'-"
k Ib
_
-
a r '?
:'"
Input Connector
' EMC4 / Amphenol / Tycol
4�
.
y
`
"r ;A
Output Connector
Insulated;
Double Insulated; Am henol
UU
"•
++ •' a"'
P ............ ............ ..........I.. ..................
Output Wire Length
.............. .P.... ...... ..
€ 0.95/3.0 %
_ ... ..
m / ft
-
/
.......... ............................ ........... .. ......
Operating Temperature Range
........................... .. .. .................
-4+185--1
-40 +85/,0-
'C %'F
�.
.^.
................................. ..........................:
Protection Rating
................... .......... ........
.. ;................
IP65/NEMA4
.................... _................... ..........
..
ch
N a rn
y c Q
v o U
Relative Humidity0
.............................................................
100
..............................................
4"
-.
` - ' .{' •
t�I Hated STC power of themodule. Module of up to 45% power tolerance allowed..
.............
............;t
a
i
Optimizer '
Datasheet
4
s
�, R4', n' �,', r ? r• r
' ` THREE PHASE THREE PHASE
PV SYSTEM DESIGN USING A SOLAREDGE INVERTER `SINGLE PHASE
_ x x .. -
u�. •., .. N. i ^^. .,n!rh..;• .i i .3 • _s., wif�S t..:b• n' ; _y� - n
_ 208V 480V.
Minimum String Length
g gt ( Optimizers)
I 8 10 18
K, s . , -„• __. ” . • " v .F , , _ r ,:y�
''
. - i e.. f i'. } r x. •. `T .i .Y 1,
r_. s• ♦ .alb.. s. r- �` . s.. Y V..,,. r• r -.��� ; .7 _ f
r "S q S- =' S -' ,:' i t L _ f. -
y
. Compatlbie.wlth Zep Groove.framed modules
..... ....... .................................. ...
Maximum String Length (Power Optimizers)
.... .......................................
.. ... .. ...................... ........... .......
.'.... 2511 25 5..
.......... ... ...................... ......................
...... ....
.......
... ,.
Maximum Power per String
15250 ] 6000 I 12750
W
`
'—.Certified Zep Compatible"". bracket ; '•= yMitigates all types of module mamatch losses, from • '•,x=
Parallel Strings of Different Lengths or Orientations
t es—
s_
manufaetu erance shading,
Attaches to'module frame without screws reduces on -roof ring tol to partial ding
t
.y....
""'
-
t` labor and mounting costs-`.Flexible'system design for maximum space utilizafion, '' '`
c _ .
;
'• .,
Power optimizer equipment grounded through the bracket - Next generation: maintenance with module -level monitoring
25°r6 more energyModule-level
voltage shutdown or installer and firefighter-
cl)o
9 O
A:-., Superior.efficiency(99.5%)
' safety k •.'s'
0 0
rn
z
cL
a
v
+,
N
V)
USA GERMANY ITALY FRANCE JAPAN
CHINA ISRAEL AUSTRALIA www.solaredge.us
O
O
GO
to
01
U
CN un m O1
� � Z6
C
N K A
W
c O tp m
• rA iDUOU
�N UcYiU
N d
.o
C W
NW
r - AA,.-' , , y 4
cl)o
9 O
L o
00
0 0
rn
z
cL
a
v
+,
N
V)
U
O
O
4�
a
..
UU
00
00
0
(V
w oo
o a)
�--I
ch
N a rn
y c Q
v o U
Y
c LL O
f0 r
� V V
a
i
Optimizer '
Datasheet
4
r - AA,.-' , , y 4
8431 Murphy Drive
lnt_ Middleton, WI 53562 USA
Telephone: 608.836.4400
Facsimile: 608.831.9279
www.intenek.com
Test Verification of Conformity
In the basis of the tests undertaken, the sample(s) of the below product have been found to comply with the requirements of
the referenced specifications at the time the tests were carried out.
nt Name & Address:
Product Description:
Ratings & Principle
Characteristics:
IronRidge, Inc.
1495 Zephyr Ave.
Hayward, CA 94544
USA
XR Rails with Integrated Grounding.
Fire Class Resistance Rating:
-Flush Mount (Symmetrical). Class A Fire Rated for Low Slope applications when using Type 1, 2
and 3, listed photovoltaic modules. Class A Fire Rated for Steep Slope applications with Type1,
2 and 3, listed photovoltaic modules. Tested with a 5" gap (distance between the bottom the
module frame and the roof covering), per the standard this system can be installed at any gap
allowed by the manufacturers installation instructions. No perimeter guarding is required.
Models: 51-61GD-005, 51-61GD-005B, 51-5000-001 and 51-65-001
Brand Name:
Relevant Standards:
Verification Issuing Office:
Date of Tests:
Test Reoort N
IronRidge Roof Mount
UL 2703 (Section 15.2 and 15.3) Standard for Safety Mounting Systems, Mounting Devices,
Clamping/Retention Devices, and Ground Lugs for Use with Flat -Plate Photovoltaic Modules
and Panels, First Edition dated Jan. 28, 2015 Referencing UL1703 Third Edition dated Nov. 18,
2014, (Section 31.2) Standard for Safety for Flat -Plate Photovoltaic Modules and Panels.
Intertek Testing Services NA, Inc.
8431 Murphy Drive
Middleton, WI 53562
08/27/2014 to 03/17/2015
101769343MID-001r1, 101769343MID-001a, 101915978MID-001 & 101999492MID-001arl-crl.
This verification is part of the full test report(s) and should be read in conjunction with them. This report does not automatically
imply product certification.
Completed by: Chad Naggs
Title: Technician-II—Eire Resistance
Signature: 1 4
Date: 03/30/2015
Reviewed by: Gregory Allen
Title: Engineering Team Lead, Fire Resistance
Signature:,2
Date: 03/30/2
This Verification is for the exclusive use of Intertek's client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are
limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense
or damage occasioned by the use of this Verification. Only the Client is authorized to permit copying or distribution of this Verification. Any use of the Intertek name or one of its
marks for the sole or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test/inspection results
referenced in this Verification ore relevant only to the sample tested/inspected. This Verification by itself does not imply that the material, product or service is or has ever been
under on Intertek certification program.
GFT -.OP -1 la (24 -MAR -2014)