HomeMy WebLinkAboutB17-1767 000-000-000 (3)i
BUILDING ENERGY ANALYSIS REPORT
BUTTE
COUNTY
BUILDING ENERGY ANALYSIS REPORT
BUTTE
COUNTY
AUG 09'201''
PROJECT:
I '
DEVELOPMENT
�
SERVICES
8)7-1767
Boelman Residence
3009 Grand Ave.
Oroville, CA 95965
Project Designer:
K.O.T.Y. Engineering
P.O. Box 4390
Chico, CA 95927
(530) 898-9810
Report Prepared by:
EI O'Hare
i
O'Hare Drafting & Designs
'
1380 East Ave, Suite 124-210
Chico, CA 95926
(530)343-5954
t
f
BUTTE COUNTY
DIVISIONM
BUILDING
q
AP5�iED
Job Number:
17-003
Date:
8/7/2017
The EnergyPro computer program has been used to perform the calculations summarized in this compliance report. This program has approval and is
authorized by the California Energy Commission for use with both the Residential and Nonresidential 2016 Building Energy Efficiency Standards.
This program developed by EnergySoft Software — www.energysoft.com.
TABLE OF CONTENTS
Cover Page
Table of Contents
Form CF -1 R -PRF -01-E Certificate of Compliance
Form RMS -1 Residential Measures Summary
Form MF -1 R Mandatory Measures Summary
HVAC System Heating and Cooling Loads Summary
Zone Load Summary
EnergyPro 7.1 by EnergySoft Job Number. ID: 17-003 User Number. 7272
1
2
3
11
12
16
17
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Residential Building Calculation Date/Time: 10:08, Thu, Aug 03, 2017
Calculation Description: Title 24 Analysis
Input File Name: Boelman.ribdl6x
CFI R -PRF -01
Page 1 of 8 ,
GENERAL INFORMATION
ENERGY USE SUMMARY
01
Project Name Residential Building
04
05
02
Calculation Description Title 24 Analysis
08
Energy Use (kTDV/ft2-yr)
03
Project Location 3009 Grand Ave.
Compliance Margin
Percent Improvement
04
City Oroville
05
Standards Version Compliance 2017
06
Zip Code 95965
07
Compliance Manager Version BEMCmpMgr 2016.2.1 (695)
08
Climate Zone CZ11
09
Software Version EnergyPro 7.1
10
Building Type Single Family
11
Front Orientation (deg/Cardinal) 180
12
Project Scope Newly Constructed
13
Number of Dwelling Units 1
14
Total Cond. Floor Area (ft2) 1857
15
Number of Zones 2
16
Slab Area (ft2) 0
17
Number of Stories 2
18
Addition Cond. Floor Area n/a
19
Natural Gas Available No
20
Addition Slab Area (ft 2) n/a
21
Glazing Percentage (%) 14.9%
COMPLIANCE RESULTS
01 Building Complies with Computer"Performafice!4_ � � r t5p/ tl
02 This building incorporates-featuresithat require field testing and/or1ve cation by aacertified�HERS r'ateriunder'th6 supervision of a CEC-approved HERS provider.
03 This building incorporates one, r more Special=Fea`t res `shown.tielow 1J U U ftel # v f1 U Q
Thisis compliance analysis is valid�,only for permLit apopl ations throug Oct er 22, 2017
Registration Number: 217-Po10268864A-000-000-0000000-0000'r Registration Dateffime: 2017-08-07 09:25:14 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF1 R-07312017-695 Report Generated at: 2017-08-03 10:09:17
ENERGY USE SUMMARY
04
05
06
07
08
Energy Use (kTDV/ft2-yr)
Standard Design
Proposed Design
Compliance Margin
Percent Improvement
Space Heating
29.08
33.48
-4.40
-15.1%
Space Cooling
43.21
36.56
6.65
15.4%
IAQ Ventilation
1.64
1.64
0.00
0.0%
Water Heating
22.96
22.96
0.00
0.0%
Photovoltaic Offset
—
0.00
0.00
--
Compliance Energy Total
96.89
94.64
2.25
2.3%
Registration Number: 217-Po10268864A-000-000-0000000-0000'r Registration Dateffime: 2017-08-07 09:25:14 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF1 R-07312017-695 Report Generated at: 2017-08-03 10:09:17
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Residential Building Calculation Date/Time: 10:08, Thu, Aug 03, 2017
Calculation Description: Title 24 Analysis Input File Name: Boelman.ribdl6x
CFI R -PRF -01
Page 2 of 8
ENERGY DESIGN RATING
Energy Design Rating (EDR) is an alternate way to express the energy performance of a building using a scoring system where 100 represents the energy performance of the Residential
Energy Services (RESNET) reference home characterization of the 2006 International Energy Conservation Code (IECC) with California modeling assumptions. A score of zero represents
the energy performance of a building that combines high levels of energy efficiency with renewable generation to"zero out' its TDV energy. Because EDR includes consideration of
components not regulated by Title 24, Part 6 (such as domestic appliances and consumer electronics), it is not used to show compliance with Part 6 but may instead be used by local
jurisdictions pursuing local ordinances under Title 24, Part 11 (CALGreen).
As a Standard Design building under the 2016 Building Energy Efficiency Standards is significantly more efficient than the baseline EDR building, the EDR of the Standard Design building
is provided for Information. Similarly, the EDR score of the Proposed Design is provided separately from the EDR value of installed PV so that the effects of efficiency and renewable
energy can both be seen
EDR of Standard Design EDR of Proposed Design EDR Value of Proposed PV Final EDR of Proposed Design
49.4 47.2 0.0 47.2
❑
Design meets Tier 1 requirement of 15% or greater code compliance margin (CALGreen A4.203.1.2.1) and QII verification prerequisite.
❑
Design meets Tier 2 requirement of 30% or greater code compliance margin (CALGreen A4.203.1.2.2) and QII verification prerequisite.
❑
Design meets Zero Net Energy (ZNE)�Design Designation requirement for Single Family in climate zone CZ11 (Red Bluff) (CALGreen A4.203.1.2.3) including on-site
Building -level Verifications:
photovoltaic (PV) renewable energy,generation sufficient to achieve a Final Energy Design Rating (EDR) of zero or less. The PV System must be verified.
REQUIRED SPECIAL FEATURES
The following are features that must bensialled as conditionfor meeting�the modeled energy§performance forthis computer analysis.
• Whole house fan•.
• Insulation above roof deck��,4
LL LK
�nc
•Window overhangs and/or fins
„ -.I,;;!► �JJJ G'
HERS FEATURE SUMMARY %r `*-A
R 5 P R 0 V i Q� R
The following is a summary of the features that must be field -verified by a certified HERS Rater as a condition for meeting the modeled energy performance for this computer analysis. Additional detail is
provided in the building components tables below.
Building -level Verifications:
• IAQ mechanical ventilation
Cooling System Verifications:
• Minimum Airflow
• Verified EER
• Verified SEER
• Fan Efficacy Watts/CFM
HVAC Distribution System Verifications:
• Duct Sealing
Domestic Hot Water System Verifications:
-- None --
Registration Number: 217-Po10268864A-000-ooa0000000-0000 Registration Date/Time: 2017-08-07 09:25:14 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF R-07312017-695 Report Generated at: 2017-08-03 10:09:17
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Residential Building
Calculation Description: Title 24 Analysis
Calculation Date/Time: 10:08, Thu, Aug 03, 2017
Input File Name: Boelman.ribd16x
CFI R -PRF -01
Page 3 of 8
BUILDING - FEATURES INFORMATION
01
02
03
04
05
06
07
Project Name
Conditioned Floor Area (ft2)
Number of Dwelling
Units
Number of Bedrooms
Number of Zones
Number of Ventilation
Cooling Systems
Number of Water
Heating Systems
Residential Building
1857
1
5
2
1
1
ZONE INFORMATION
01
02
03
04
05
06
07
Zone Name
Zone Type
HVAC System Name
Zone Floor Area
(ft2)
Avg. Ceiling
Height
Water Heating System 1
Water Heating System 2
Zone 1
Conditioned
HVAC Systeml
1214
8
DHW Sys 1
Window & Door Area (ft2)
Zone 2
Conditioned
HVAC Systeml
643
8
DHW Sys 1
117.5
OPAQUE SURFACES
1
01
i X02 03
04
05
06
07
08
Name
1 Zone=— �_ �,., Construction
Azimuth
Orientation Gross Area (ft)
Window & Door Area (ft2)
Tilt (deg)
Front Wall
Zone.1 ,,R'AWall, ._ .. 7 �1�80
Front
420
117.5
90
Left Wall
Zone,11 R-1911Wall, iU)
1 ',�27*0
rge—q
224
20
90
Rear Wali
e one,1� 4 N�R:;,1y9�,Vall, I I Nk
; 1 f,,.,0) n
I I JBack �t ry
420
109.3
90
Right Wall
��/
Zone ,l R A ,R-19 Wal f b
i "1 L9 ,"t
T"< Right r,
224
30
90
Raised Floor
Zone 1 F .-. R-19 Floor Crawlspace
%— r ,
1214
Front Wall 2
Zone 2 R-19 Wall
180
Front
292
36
90
Left Wail 2
Zone 2 R-19 Wali
270
Left
164
12
90
Rear Wall 2
Zone 2 R-19 Wali
0
Back
292
0
90
Right Wall 2
Zone 2 R-19 Wall
90
Right
164
12
90
Roof
Zone 2 R-38 HP Attic Option A
643
ATTIC
01 02 03 04 05 06 07 08
Name Construction Type Roof Rise Roof Reflectance Roof Emittance Radiant Barrier Cool Roof
Attic Zone 2 Attic RoofZone 2 Ventilated 12 0.1 0.85 Yes No
Registration Number: 217-Po10268864A-000-000-0000000-0000 Registration Date/Time: 2017-08-07 09:25:14 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF R-07312017-695 Report Generated at: 2017-08-03 10:09:17
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Residential Building Calculation Date/Time: 10:08, Thu, Aug 03, 2017
Calculation Description: Title 24 Analysis Input File Name: Boelman.ribd16x
CFI R -PRF -01
Page 4 of 8 -
FENESTRATION / GLAZING
rYe T w• r.,4 -
01 r
1 1 L- I _% 7 r- 02A �..r V r L-0 i- If `t
03
04
Name
Side of Building
01
02
03
04
05
06
07
08
09
10
Name
Type
Surface (Orientation -Azimuth) Width (ft)
Height
(ft)
Multiplier
Area
(ft)
1.1 -factor
SHGC
Exterior Shading
Living Room Windows
Window
Front Wall (Front -180)
6.0
5.0
1
30.0
0.32
0.25
Insect Screen (default)
Master Bath Window
Wndow
Front Wall (Front -180)
2.5
3.0
1
7.5
0.32
0.25
Insect Screen (default)
Master BedRoom Windows
Window
Front Wall (Front -180)
6.0
5.0
1
30.0
0.32
0.25
Insect Screen (default)
Bedroom Front Window
Window
Front Wali (Front -180)
3.0
5.0
1
15.0
0.32
0.25
Insect Screen (default)
Dining Front Window
Window
Front Wall (Front -180)
3.0
5.0
1
-15.0
0.32
0.25
Insect Screen (default)
BedRoom Windows
Window
Rear Wall (Back -0)
6.0
5.0
1
00.0
0.32
0.25
Insect Screen (default)
Kitchen Window
Window
Rear Wall (Back -0)
--
--
1
11.0
0.32
0.25
Insect Screen (default)
French Doors
Window ! 1
Rear Wall (Back -0)
--
--
1
33.3
0.32
0.25
Insect Screen (default)
Dining Window
Wndow
Rear Wall (Back -0)
-
-
1
15.0
0.32
0.25
Insect Screen (default)
Dining Room Windows
Window
Right Wall (Right -90)
6.0
5.0
1
30.0
0.32
0.25
Insect Screen (default)
Dormer Windows
Wndow '-"---.Front
Wall-
.Front-Wall-2(Front-180)
--
--
1
36.0
0.32
0.25
Insect Screen (default)
Left Window
Wndow % Left Wall 2
1
1
12.0
0.32
0.25
Insect Screen (default)
Right Window
Windowr�
Right Wall.2 (Righrt90)
+�
,�-
J(J
�, 12.0
0.32
0.25
Insect Screen (default)
OPAQUE DOORS
rYe T w• r.,4 -
01 r
1 1 L- I _% 7 r- 02A �..r V r L-0 i- If `t
03
04
Name
Side of Building
Area (ft2)
U -factor
Main Entry Door
Front Wall
,' 20.0
0.50
Master Bedroom Door
Left Wall
20.0
0.50
Rear Door
Rear Wall
20.0
0.50
Registration Number: 217-Po10268864A-000-000-0000000-0000 Registration DateRme: 2017-08-07 09:25:14 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF1 R-07312017-695 Report Generated at: 2017-08-03 10:09:17
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Residential Building Calculation Date/Time: 10:08, Thu, Aug 03, 2017
Calculation Description: Title 24 Analysis
Input File Name: Boelman.ribd16x
CF1 R -PRF -01
Page 5 of 8
OVERHANGS AND FINS
01
,�- —02--J/
t—,03
04
05
06
07
��
�� `T
Total Cavity
Winter Design
01
02
03
04
05
06
07
08
09
10
11
12
13
14
Floor Surface: Carpeted9/
Floors O.ver�
Overhang
a ri�Cz
)rR
Left Fin
R-19 Floor Crawlspace
Crawlspace
Wood Framed Floor
Right Fin
19
0.049
Window
Depth
Dist Up
Left
Extent
Right
Extent
Flap Ht.
Depth
Top Up
Distl-
Bot Up
Depth
Top Up Dist R
Bot Up
Living Room Windows
9
0.1
9
9
0
0
0
0
0
0
0
0
0
Master Bath Window
9
0.1
9
9
0
0
0
0
0
0
0
0
0
Master BedRoom Windows
9
0.1
9
9
0
0
0
0
0
0
0 1
0
0
Bedroom Front Window
9
0.1
9
9
0
0
0
0
0
0
0
0
0
Dining Front Window
9
0.1
9
9
0
0
0
0
0
0
0
0
0
BedRoom Windows
1
0.1
1
1
0
0
0
0
0 1
0
0
0
0
Dining Room Windows
1 n
0.1
1
1
0
0
0
0
0 1
0
0
0
0
OPAQUE SURFACE CONSTRUCTIONS / A \
01
,�- —02--J/
t—,03
04
05
06
07
��
�� `T
Total Cavity
Winter Design
Construction Name
SurfaceYType
(Construction Type
n IFiamingl
R-valire
U -value
Assembly Layers
'
I
Floor Surface: Carpeted9/
Floors O.ver�
�o
a ri�Cz
)rR
Floor Deck: Wood Sidin /sheathin decking
R-19 Floor Crawlspace
Crawlspace
Wood Framed Floor
_ 2x6 @ 16 m. O.C. _
19
0.049
Cavity/Frame: R -19/2x6
✓
rl r—
M r-1 M k-10
V 1
-
Inside Finish: Gypsum Board
• Cavity/Frame: R -19/2x6
R-19 Wali
Exterior Walls
Wood Framed Wall
2x6 @ 16 in. O.C.
R 19
0.072
Exterior Finish: 3 Coat Stucco
• Floor Surface: Carpeted
• Floor Deck: Wood Siding/sheathing/decking
• Cavity/Frame: R -19/2x6
R-19 Floor No Crawlspace
Interior Floors
Wood Framed Floor
2x6 @ 16 in. O.C.
R19
0.048
Ceiling Below Finish: Gypsum Board
• Cavity / Frame: no insul. 12x4 Top Chrd
• Roof Deck: Wood Siding/sheathing/decking
2x4 Top Chord of Roof Truss @ 24
Above Deck Insulation: R8 Sheathing
Attic RoofZone 2
Attic Roofs
Wood Framed Ceiling
in. O.C.
none
0.103
Roofing: Light Roof (Asphalt Shingle)
• Inside Finish: Gypsum Board
Ceilings (below
Cavity/Frame: R-9.1 /2x4
R-38 HP Attic Option A
attic)
Wood Framed Ceiling
2x4 @ 24 in. O.C.
R 38
0.025
Over Ceiling Joists: R-28.9 insul.
BUILDING ENVELOPE - HERS VERIFICATION
01 02 03 04
Quality Insulation Installation (QII) Quality Installation of Spray Foam Insulation Building Envelope Air Leakage CFM50
Not Required Not Required Not Required —
Registration Number: 217-Po10268864A-000-000-0000000-0000 Registration Date/Time: 2017-08-07 09:25:14 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF1 R-07312017-695 Report Generated at: 2017-08-03 10:09:17
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Residential Building Calculation Date/Time: 10:08, Thu, Aug 03, 2017
Calculation Description: Title 24 Analysis
Input File Name: Boelman.ribdl6x
CFI R -PRF -01
Page 6 of 8
WATER HEATING SYSTEMS
01 02 03 04 05 06
Name System Type Distribution Type Water Heater Number of Heaters Solar Fraction (%)
DHW Sys 1 DHW Standard DHW Heater 1 (1) 1 .0%
WATER HEATERS
01
02
03
04
05
06
07
08
09
10
11
Other Heating and'Cool ing
Heating Component 1
SystI I i '0' t= r =:N
Cooling Component 1
HVAC Fan 1
Air Distribution System 1
Tank
Energy
EER SEER
Tank Insulation
Compressor Type
HERS Verification
Tank Location or
SplitAirCond
Heater
12.515
Number
Volume
Factor or
Input
R -value
Standby Loss /
Ambient
Name
Element Type
Tank Type
of Units
(gal)
Efficiency
Rating/Pilot
(Int/Ext)
Recovery Eff
NEEA Heat Pump Type
Condition
DHW Heater 1
Gas
Instan a Small
1
0
0.82 EF
199,000 Btu/hr
R-0
n/a
r0
n/a
SPACE CONDITIONING SYSTEMS A
01
02 03
04
05
06
SC Sys Name f
l _System Type Heating Unit Name
Cooling Unit Name
Fan Name
Distribution Name
HVAC Systeml
Other Heating and'Cool ing
Heating Component 1
SystI I i '0' t= r =:N
Cooling Component 1
HVAC Fan 1
Air Distribution System 1
HVAC -HEATING UNIT TYPES 11 /� (`� ' 11 W Ii!;4* II %
IE
1P it M(
01 �� `�� �.� 11 `a' r02= U `i..1
U ff
L U it 030 1J 04
Name '` H L K System Type K
V V i
L) Numbey'of Units Efficiency
Heating Component 1 CntrlFumace
Verified EER
1 94 AFUE
HVAC - COOLING UNIT TYPES
01
02
03
04 05
06
07
08
Verified Airflow
Airflow Target
Verified EER
Efficiency
Verified Refrigerant
Charge
Cooling Component 1 -hers -cool
Required
Name
System Type
Number of Units
EER SEER
Zonally Controlled
Compressor Type
HERS Verification
Cooling Component 1
SplitAirCond
1
12.515
Not Zonal
Single Speed
Cooling Component
1 -hers -cool
HVAC COOLING - HERS VERIFICATION
01
02
03
04
05
06
Name
Verified Airflow
Airflow Target
Verified EER
Verified SEER
Verified Refrigerant
Charge
Cooling Component 1 -hers -cool
Required
350
Required
Required
Not Required
Registration Number: 217-Po10268864A-000-ooa0000000-0000 Registration Date/Time: 2017-08-07 09:25:14 HERS Provider: CaiCERTS inc.
CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF1 R-07312017-695 Report Generated at: 2017-08-03 10:09:17
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Residential Building Calculation Date/Time: 10:08, Thu, Aug 03, 2017
Calculation Description: Title 24 Analysis
Input File Name: Boelman.ribd16x
CFI R -PRF -01
Page 7 of 8
HVAC - DISTRIBUTION SYSTEMS
01 02
03
04
05
06
07
Name Type
Duct Leakage
Insulation R -value
Duct Location
Bypass Duct
HERS Verification
Air Distribution System 1 DuctsAttic
Sealed and tested
8
Attic
None
Air Distribution System
1 -hers -dist
HVAC DISTRIBUTION - HERS VERIFICATION
01
02
03
04
05
06
07
08
Name
Duct Leakage
Verification
Duct Leakage
Target (%)
Verified Duct
Location
Verified Duct
Design
Buried
Ducts
Deeply Buried
Ducts
Low -leakage
Air Handler
Air Distribution System 1 -hers -dist
Required
5.0
Not Required
Not Required
Not Required
Not Required
—
HVAC -FAN SYSTEMS A
01 02 03 04
Name Type Fan Power (Watts/CFM) HERS Verification
HVAC Fan 1 �...`'-�--� Single_Speed PSC Furnace Fan 0.58 HVAC Fan 1 -hers -fan
HVAC FAN SYSTEMS -HERS VERIFICATION ��'
-- "
/
01 � r'
{�
r
� � i 1� Ii"- 02 11 '� g 11 11l)1j if 03
Name I , `���
t3 ` t^Verified Fan Watt Drawl i<l U U 4 Required Fan Efficiency (Watts/CFM)
HVAC Fan 1 -hers -fan
H E K` P Require Y I Q E H 0.58
IAQ (Indoor Air Quality) FANS
01
02
03
04
05
06
Dwelling Unit
IAQ CFM
IAQ Watts/CFM
IAQ Fan Type
IAQ Recovery
Effectiveness(%)
HERS Verification
SFam IAQVentRpt
64
0.25
Default
0
Required
COOLING VENTILATION
01 02 03 04 05 06
Name Airflow Rate (CFM/ft2) Cooling Vent CFM Cooling Vent Watts/CFM Total Watts Number of Fans
WH Fan 1 2.4259558427571352 4505 0.140289 632 1
Registration Number: 217-Po10268864A-000-000-0000000-0000 Registration Date/Time: 2017-08-07 09:25:14 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF1 R-07312017-695 Report Generated at: 2017-08-03 10:09:17
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Residential Building Calculation DatefTime: 10:08, Thu, Aug 03, 2017
Calculation Description: Title 24 Analysis Input File Name: Boelman.ribd16x
CFI R -PRF -01
Page 8 of 8
DOCUMENTATION AUTHOR'S DECLARATION STATEMENT
1. 1 certify that this Certificate of Compliance documentation is accurate and complete.
Documentation Author Name:
Documentation Author Signature:
Z-7617A?�
EI O'Hare
Company:
Signature Date:
O'Hare Drafting & Designs
2017-08-07 09:25:14
Address:
CEA/HERS Certification Identification (If applicable):
30 Landing Circle, Suite 103
N/A
City/State/Zip:
Phone:
Chico, CA 95973
530-343-5954
RESPONSIBLE PERSON'S DECLARATION STAT
xEMENT
I certify the following under penalty of perjury, under the laws of the State of California:
1. 1 am eligible under Division 3 of the Businessland Professions Code to accept responsibility for the building design identified on this Certificate of Compliance.
2. 1 certify that the energy features and perfor'ma'nce specifications identified on this Certificate of Compliance conform to the requirements of Title 24, Part 1 and Part 6 of the California Code of
Regulations. - .�
3. The building design features or system-designfeatures identified-on�this''Certificate of Compliance are consistent with the information provided on other applicable compliance documents,
worksheets, calculations, plans nd specifications sutim', itted io.the enforcemenitagency for approval withrnis pyilding permit application.
+
Responsible Designer Name:
"
iResponsible besigner Signature:
4
,,
EI O'Hare
.
�� 1 0)t n 11 -1 �R�tPi
Company: f /
Y HERS
Date Signed: 1W
09:25:14
O'Hare Drafting & Designs
2017-08 07
Address:
License:
30 Landing Circle, Suite 103
N/A
City/State/Zip:
Phone:
Chico, CA 95973
530-343-5954
Digitally signed by CaICERTS. This digital signature is provided in order to secure the content of this registered document, and in no way implies Registration
Provider responsibility for the accuracy of the information.
Registration Number: 217-PO10268864A-000-000-0000000-0000 Registration Date/Time: 2017-08-07 09:25:14
CA Building Energy Efficiency Standards - 2016 Residential Compliance Report Version - CF1 R-07312017-695
E 1'
Easy to Verify
at CaICERTS.com
HERS Provider: CaICERTS inc.
Report Generated at: 2017-08-03 10:09:17
RESIDENTIAL MEASURES SUMMARY
RMS -1
Project Name
Boelman Residence
Building Type m Single Family ❑ Addition Alone
❑ Multi Family ❑ Existing+ Addition/Alteration
Date
8/7/2017
Project Address
3009 Grand Ave. Oroville
California Energy Climate Zone
CA Climate Zone 11
Total Cond. Floor Area
1,857
Addition
n/a
# of Units
1
INSULATION
Construction Type
Area
Cavi (ft)Special Features Status
Floor Wood Framed w/Crawl Space R 19 1,214
New
Wall Wood Framed R 19 1,863
New
Door Opaque Door - no insulation 60
New
Demising Wood Framed w/o Crawl Space R 19 1,857
New
Roof Wood Framed Attic R 38 643 Add=R-8.0
New
FENESTRATION I Total Area: 277 Glazing Percentage: 14.9%1New/Altered
Orientation Area ft2 U -Fac SHGC Overhang Sidefins
Average U -Factor: 0.32
Exterior Shades Status
Front (S) 97.5 0.320
0.25 9.0 none
Bug Screen New
Rear (N) 30.0 0.320
0.25 1.0 none
Bug Screen New
Rear (N) 59.3 0.320
0.25 none none
Bug Screen New
Right (E) 30.0 0.320
0.25 1.0 none
Bug Screen New
Front (S) 36.0 0.320
0.25 none none
Bug Screen New
Left (lM 12.0 0.320
0.25 none none
Bug Screen New
Right (E) 12.0 0.320
0.25 none none
Bug Screen New
HVAC SYSTEMS
Qty. Heating Min. Eff
Cooling Min. Eff
Thermostat Status
1 Central Furnace 94% AFUE
Split Air Conditioner 15.0 SEER
Setback
New
HVAC DISTRIBUTION
Location Heating
Cooling Duct Location
Duct
R -Value Status
HVAC System Ducted
Ducted Attic
8.0 New
WATER HEATING
Qty. Type Gallons Min. Eff Distribution Status
1 Small Instantaneous Gas 0
0.82 Standard
New
EnemvPro 7.1 by EnemySoft User Number: 7272
/D: 17-003 Pae 11 of 17
+ 2016 Low -Rise Residential Mandatory Measures Summary
NOTE: Low-rise residential buildings subject to the Energy Standards must comply with all applicable mandatory measures, regardless of the compliance approach
used. Review the respective section for more information. 'Exceptions may apply.
(Original 08/20161
Building Envelope Measures:
§ 110.6(a)l:
Air Leakage. Manufactured fenestration, exterior doors, and exterior pet doors must limit air leakage to 0.3 cfm/ftz or less when tested per
NFRC-400 or ASTM E283 or AAMA/WDMA/CSA 101/I.S.2/A440-2011.'
§ 110.6(a)5:
Labeling. Fenestration products must have a label meeting the requirements of § 10-111(a).
§ 110.6(b):
Field fabricated exterior doors and fenestration products must use U -factors and solar heat gain coefficient (SHGC) values from TABLES
110.6-A and 110.6-B for compliance and must be caulked and/or weatherstri ed.'
§ 110.7:
Air Leakage. All joints, penetrations, and other openings in the building envelope that are potential sources of air leakage must be caulked,
asketed, or weather stripped.
§ 110.8(a):
Insulation Certification by Manufacturers. Insulation specified or installed must meet Standards for Insulating Material.
§ 110.8(g):
Insulation Requirements for Heated Slab Floors. Heated slab floors must be insulated per the requirements of § 110.8(g).
§ 110.8(i):
Roofing Products Solar Reflectance and Thermal Emittance. The thermal emittance and aged solar reflectance values of the roofing
material must meet the requirements of § 110.8 i when the installation of a cool roof is specified on the CF1 R.
§ 110.80):
Radiant Barrier. A radiant barrier must have an emittance of 0.05 or less and be certified to the Department of Consumer Affairs.
Ceiling and Rafter Roof Insulation. Minimum R-22 insulation in wood -frame ceiling; or the weighted average U -factor must not exceed 0.043.
Minimum R-19 or weighted average U -factor of 0.054 or less in a rafter roof alteration. Attic access doors must have permanently attached
§ 150.0(a):
insulation using adhesive or mechanical fasteners. The attic access must be gasketed to prevent air leakage. Insulation must be installed in
direct contact with a continuous roof or ceiling which is sealed to limit infiltration and exfiltration as specified in § 110.7, including but not limited
to placing insulation either above or below the roof deck or on top of a drywall ceiling.*
§ 150.0(b):
Loose -fill Insulation. Loose fill insulation must meet the manufacturer's required density for the labeled R -value.
Wall Insulation. Minimum R-13 insulation in 2x4 inch wood framing wall or have a U -factor of 0.102 or less (R-19 in 2x6 or U -factor of 0.074 or
§ 150.0(c):
less). Opaque non -framed assemblies must have an overall assembly U -factor not exceeding 0.102, equivalent to an installed value of R-13 in a
wood framed assembly.*
§ 150.0(d):
Raised -floor Insulation. Minimum R-19 insulation in raised wood framed floor or 0.037 maximum U -factor.'
§ 150.0(f):
Slab Edge Insulation. Slab edge insulation must meet all of the following: have a water absorption rate, for the insulation material alone without
facings, no greater than 0.3%; have a water vapor permeance no greater than 2.0 perm/inch; be protected from physical damage and UV light
deterioration; and, when installed as part of a heated slab floor, meet the requirements of § 1 10.8 .
Vapor Retarder. In Climate Zones 1-16, the earth floor of unvented crawl space must be covered with a Class I or Class II vapor retarder. This
§ 150.0(g)l:
requirement also applies to controlled ventilation crawls ace for buildings complying with the exception to § 150.0(d).
Vapor Retarder. In Climate Zones 14 and 16, a Class I or Class II vapor retarder must be installed on the conditioned space side of all
§ 150.0(8)2:
insulation in all exterior walls, vented attics, and unvented attics with air -permeable insulation.
150.0
§ (q)'
Fenestration Products. Fenestration, including skylights, separating conditioned space from unconditioned space or outdoors must have a
maximum Ll -factor of 0.58; or the weighted average U -factor of all fenestration must not exceed 0.58.'
Fireplaces, Decorative Gas Appliances, and Gas Log Measures:
§ 150.0(e)1A:
Closable Doors. Masonry or factory -built fireplaces must have a closable metal or glass door covering the entire opening of the firebox.
§ 150.0(e)1 B:
Combustion Intake. Masonry or factory -built fireplaces must have a combustion outside air intake, which is at least six square inches in area
and is equipped with a readily accessible, operable, and tight -fitting damper or combustion -air control device.'
§ 150.0(e)1C:
Flue Damper. Masonry or factory -built fireplaces must have a flue damper with a readily accessible control.'
§ 150.0(e)2:
Pilot Light. Continuous burning pilot lights and the use of indoor air for cooling a firebox jacket, when that indoor air is vented to the outside of
the building, are prohibited.
Space Conditioning, Water Heating, and Plumbing System Measures:
§ 110.0-§ 110.3:
Certification. Heating, ventilation and air conditioning (HVAC) equipment, water heaters, showerheads, faucets, and all other regulated
appliances must be certified by the manufacturer to the Energy Commission.'
§ 110.2(a):
HVAC Efficiency. Equipment must meet the applicable efficiency requirements in TABLE 110.2-A through TABLE 110.2-K.'
Controls for Heat Pumps with Supplementary Electric Resistance Heaters. Heat pumps with supplementary electric resistance heaters
§ 110.2(b):
must have controls that prevent supplementary heater operation when the heating load can be met by the heat pump alone; and in which the
cut -on temperature for compression heating is higher than the cut -on temperature for supplementary heating, and the cutoff temperature for
compression heating is higher than the cutoff temperature for supplementary heating.'
§ 110.2(c):
Thermostats. All unitary heating or cooling systems not controlled by a central energy management control system (EMCS) must have a
setback thermostat.'
Water Heating Recirculation Loops Serving Multiple Dwelling Units. Water heating recirculation loops serving multiple dwelling units must
§ 110.3(c)5:
meet the air release valve, backflow prevention, pump priming, pump isolation valve, and recirculation loop connection requirements of §
110.3(c)5.
§ 110.3(c)7:
Isolation Valves. Instantaneous water heaters with an input rating greater than 6.8 kBTU/hr (2 kW) must have isolation valves with hose bibbs
or other fittings on both cold water and hot water lines of water heating systems to allow for water tank flushing when the valves are closed.
§ 110.5: •
Pilot Lights. Continuously burning pilot lights are prohibited for natural gas: fan -type central furnaces; household cooking appliances (appli-
ances without an electrical supply voltage connection with pilot lights that consume less than 150 Btu/hr are exempt); and pool ands a heaters.'
Building Cooling and Heating Loads. Heating and/or cooling loads are calculated in accordance with ASHRAE Handbook, Equipment
§ 150.0(h)l:
Volume, Applications Volume, and Fundamentals Volume; SMACNA Residential Comfort System Installation Standards Manual; or ACCA
Manual J using design conditions specified in § 150.0(h)2.
2016 Low -Rise Residential Mandatory Measures Summary
§ 150.0(h)3A:
Clearances. Installed air conditioner and heat pump outdoor condensing units must have a clearance of at least 5 feet from the outlet of any
dryer vent.
§ 150.0(h)3B:
Liquid Line Drier. Installed air conditioner and heat pump systems must be equipped with liquid line filter driers if required, as specified by
manufacturer's instructions.
§ 150.00)1:
Storage Tank Insulation. Unfired hot water tanks, such as storage tanks and backup storage tanks for solar water -heating systems, must have
R-12 external insulation or R-16 internal insulation where the internal insulation R -value is indicated on the exterior of the tank.
Water piping and cooling system line insulation. For domestic hot water system piping, whether buried or unburied, all of the following must
be insulated according to the requirements of TABLE 120.3-A: the first 5 feet of hot and cold water pipes from the storage tank; all piping with a
§ 150.00)2A:
nominal diameter of 3/4 inch or larger; all piping associated with a domestic hot water recirculation system regardless of the pipe diameter;
piping from the heating source to storage tank or between tanks; piping buried below grade; and all hot water pipes from the heating source to
kitchen fixtures.'
§ 150.00)2B:
Water piping and cooling system line insulation. All domestic hot water pipes that are buried below grade must be installed in a water proof
and non -crushable casing or sleeve.'
§ 150.00)2C:
Water piping and cooling system line insulation. Pipe for cooling system lines must be insulated as specified in § 150.00)2A. Distribution
piping for steam and h dronic heating systems or hot waters stems must meet the requirements in TABLE 120.3-A.'
§ 150.00)3:
Insulation Protection. Insulation must be protected from damage, including that due to sunlight, moisture, equipment maintenance, and wind.
Insulation Protection. Insulation exposed to weather must be installed with a cover suitable for outdoor service. For example, protected by
§ 150.00)3A:
aluminum, sheet metal, painted canvas, or plastic cover. The cover must be water retardant and provide shielding from solar radiation that can
cause degradation of the material.
§ 150.00)36:
Insulation Protection. Insulation covering chilled water piping and refrigerant suction piping located outside the conditioned space must have a
Class I or Class II vapor retarder.
Gas or Propane Systems. Systems using gas or propane water heaters to serve individual dwelling units must include all of the following: a
§ 150.0(n)1:
120V electrical receptacle within 3 feet of the water heater; a Category III or IV vent, or a Type B vent with straight pipe between the outside
termination and the space where the water heater is installed; a condensate drain that is no more than 2 inches higher than the base of the
water heater, and allows natural draining without pump assistance; and a gas supply line with a capacity of at least 200,000 Btu/hr.
§ 150.0(n)2:
Recirculating Loops. Recirculating loops serving multiple dwelling units must meet the requirements of § 110.3(c)5.
§ 150.0(n)3:
Solar Water -heating Systems. Solar water -heating systems and collectors must be certified and rated by the Solar Rating and Certification
-Corporation SRCC or by a listing agency that is approved by the Executive Director.
Ducts and Fans Measures:
§ 110.8(d)3:
Ducts. Insulation installed on an existing space -conditioning duct must comply with § 604.0 of the California Mechanical Code (CMC). If a
contractor installs the insulation, the contractor must certify to the customer, in writing, that the insulation meets this requirement.
CMC Compliance. All air -distribution system ducts and plenums must be installed, sealed, and insulated to meet the requirements of CMC
§§ 601.0, 602.0, 603.0, 604.0, 605.0 and ANSI/SMACNA-006-2006 HVAC Duct Construction Standards Metal and Flexible 3rd Edition. Portions
of supply -air and return -air ducts and plenums must be insulated to a minimum installed level of R-6.0 (or higher if required by CMC § 605.0) or
a minimum installed level of R-4.2 when entirely in conditioned space as confirmed through field verification -and diagnostic testing
§ 150.0(m)1:
(RA3.1.4.3.8). Connections of metal ducts and inner core of flexible ducts must be mechanically fastened. Openings must be sealed with
mastic, tape, or other duct -closure system that meets the applicable requirements of UL 181, UL 181A, or UL 181 B or aerosol sealant that
meets the requirements of UL 723. If mastic or tape is used to seal openings greater than % inch, the combination of mastic and either mesh or
tape must be used. Building cavities, support platforms for air handlers, and plenums designed or constructed with materials other than sealed
sheet metal, duct board or flexible duct must not be used for conveying conditioned air. Building cavities and support platforms may contain
ducts. Ducts installed in cavities and support platforms must not be compressed to cause reductions in the cross-sectional area of the ducts.'
Factory -Fabricated Duct Systems. Factory -fabricated duct systems must comply with applicable requirements for duct construction,
§ 150.0(m)2:
connections, and closures; joints and seams of duct systems and their components must not be sealed with cloth back rubber adhesive duct
tapes unless such tae is used in combination with mastic and draw bands.
§ 150.0(m)3:
Field -Fabricated Duct Systems. Field -fabricated duct systems must comply with applicable requirements for: pressure -sensitive tapes,
mastics, sealants, and other requirements specified for duct construction.
§ 150.0(m)7:
Backdraft Dampers. All fan systems that exchange air between the conditioned space and the outside of the building must have backdraft or
automatic dampers.
§ 150.0(m)8:
Gravity Ventilation Dampers. Gravity ventilating systems serving conditioned space must have either automatic or readily accessible,
manually operated dampers in all openings to the outside, except combustion inlet and outlet air openings and elevator shaft vents.
Protection of Insulation. Insulation must be protected from damage, including that due to sunlight, moisture, equipment maintenance, and
§ 150.0(m)9:
wind. Insulation exposed to weather must be suitable for outdoor service. For example, protected by aluminum, sheet metal, painted canvas, or
plastic cover. Cellular foam insulation must be protected as above or painted with a coating that is water retardant and provides shielding from
solar radiation.
§ 150.0(m)10:
Porous Inner Core Flex Duct. Porous inner core flex duct must have a non -porous layer between the inner core and outer vapor barrier.
Duct System Sealing and Leakage Test. When space conditioning systems use forced air duct systems to supply conditioned air to an
§ 150.0(m)11:
occupiable space, the ducts must be sealed and duct leakage tested, as confirmed through field verification and diagnostic testing, in
accordance with § 150.0(m) 11 and Reference Residential Appendix RA3.
Air Filtration. Mechanical systems that supply air to an occupiable space through ductwork exceeding 10 feet in length and through a thermal
§ 150.0(m)12:
conditioning component, except evaporative coolers, must be provided with air filter devices that meet the design, installation, efficiency,
pressure drop,and labeling requirements of § 150.0 m 12.
2016 Low -Rise Residential Mandatory Measures Summary
Duct System Sizing and Air Filter Grille Sizing. Space conditioning systems that use forced air ducts to supply cooling to an occupiable
space must have a hole for the placement of a static pressure probe (HSPP), or a permanently installed static pressure probe (PSPP) in the
§ 150.0(m)13:
supply plenum. The space conditioning system must also demonstrate airflow z 350 CFM per ton of nominal cooling capacity through the return
grilles, and an air -handling unit fan efficacy <_ 0.58 WICFM as confirmed by field verification and diagnostic testing, in accordance with
Reference Residential Appendix RA3.3. This applies to both single zone central forced air systems and every zone for zonally controlled central
forced airs stems.'
Ventilation for Indoor Air Quality. All dwelling units must meet the requirements of ASHRAE Standard 62.2. Neither window operation nor
§150.0(0):
continuous operation of central forced air system air handlers used in central fan integrated ventilation systems are permissible methods of
providing whole -building ventilation.
§ 150.0(o)1A:
Field Verification and Diagnostic Testing. Whole -building ventilation airflow must be confirmed through field verification and diagnostic
testing, in accordance with Reference Residential Appendix RA3.7.
Pool and Spa Systems and Equipment Measures:
Certification by Manufacturers. Any pool or spa heating system or equipment must be certified to have all of the following: a thermal efficiency
§ 110.4(a):
that complies with the Appliance Efficiency Regulations; an on-off switch mounted outside of the heater that allows shutting off the heater
without adjusting the thermostat setting; a permanent weatherproof plate or card with operating instructions; and must not use electric
resistance heating.*
§ 110.4(b)1:
Piping. Any pool or spa heating equipment must be installed with at least 36 inches of pipe between the filter and the heater, or dedicated
suction and return lines, or built-in or built-up connections to allow for future solar heating.
§ 110.4(b)2:
Covers. Outdoor pools or spas that have a heat pump or gas heater must have a cover.
§ 110.4(b)3:
Directional inlets and time switches for pools. Pools must have directional inlets that adequately mix the pool water, and a time switch that
will allow all pumps to be set or programmed to run only during off-peak electric demand periods.
§ 110.5:
Pilot Light. Natural gas pool and spa heaters must not have a continuously burning pilot light.
150.0
§ (p)'
Pool Systems and Equipment Installation. Residential pool systems or equipment must meet the specified requirements for pump sizing, flow
rate, piping, filters, and valves.'
Lighting Measures:
§ 110.9:
Lighting Controls and Components. All lighting control devices and systems, ballasts, and luminaires must meet the applicable requirements
of § 110.9.'
§ 110.9(e):
JA8 High Efficacy Light Sources. To qualify as a JA8 high efficacy light source for compliance with § 150.0(k), a residential light source must
be certified to the Energy Commission according to Reference Joint Appendix JA8.
§ 150.0(k)1A:
Luminaire Efficacy. All installed luminaires must be high efficacy in accordance with TABLE 150.0-A.
Blank Electrical Boxes. The number of electrical boxes that are more than 5 feet above the finished floor and do not contain a luminaire or
§ 150.0(k)1 B:
other device must be no greater than the number of bedrooms. These electrical boxes must be served by a dimmer, vacancy sensor control, or
fanspeed control.
Recessed Downlight Luminaires in Ceilings. Luminaires recessed into ceilings must meet all of the requirements for: insulation contact (IC)
§ 150.0(k)1C:
labeling; air leakage; sealing; maintenance; and socket and light source as described in § 150.0(k)1C. A JA8-2016-E light source rated for
elevated temperature must be installed by final inspection in all recessed downli ht luminaires in ceilings.
§ 150.0(k)1 D:
Electronic Ballasts. Ballasts for fluorescent lamps rated 13 watts or greater must be electronic and must have an output frequency no less than
20 kHz.
Night Lights. Permanently installed night lights and night lights integral to installed luminaires or exhaust fans must be rated to consume no
§ 150.0(k)1 E:
more than 5 watts of power per luminaire or exhaust fan as determined in accordance with § 130.0(c). Night lights do not need to be controlled
by vacancy sensors.
§ 150.0(k)1 F:
Lighting Integral to Exhaust Fans. Lighting integral to exhaust fans (except when installed by the manufacturer in kitchen exhaust hoods)
must meet the applicable requirements of § 150.0(k).*
Screw based luminaires. Screw based luminaires must not be recessed downlight luminaires in ceilings and must contain lamps that comply
§ 150.0(k)1G:
with Reference Joint Appendix JA8. Installed lamps must be marked with "JA8-2016" or "JA8-2016-E" as specified in Reference Joint Appendix
JA8.'
§ 150.0(k)1 H:
Enclosed Luminaires. Light sources installed in enclosed luminaires must be JA8 compliant and must be marked with "JA8-2016-E."
§ 150.0(k)2A:
Interior Switches and Controls. All forward phase cut dimmers used with LED light sources must comply with NEMA SSL 7A.
§ 150.0(k)2B:
Interior Switches and Controls. Exhaust fans must be switched separately from lighting systems.'
§ 150.0(k)2C:
Interior Switches and Controls. Luminaires must be switched with readily accessible controls that permit the luminaires to be manually
switched ON and OFF.
§ 150.0(k)2D:
Interior Switches and Controls. Controls and equipment must be installed in accordance with manufacturer's instructions.
§ 150.0(k)2E:
Interior Switches and Controls. No control must bypass a dimmer or vacancy sensor function if the control is installed to comply with
150.0(k).
§ 150.0(k)2F:
Interior Switches and Controls. Lighting controls must comply with the applicable requirements of § 110.9.
Interior Switches and Controls. An energy management control system (EMCS) may be used to comply with dimmer requirements if it:
§ 150.0(k)2G:
functions as a dimmer according to § 110.9; meets the Installation Certificate requirements of § 130.4; meets the EMCS requirements of §
130.5(f); and meets all other requirements in § 150.0(k)2.
Interior Switches and Controls. An EMCS may be used to comply with vacancy sensor requirements in § 150.0(k) if it meets all of the
§ 150.0(k)2H:
following: it functions as a vacancy sensor according to § 110.9; the Installation Certificate requirements of § 130.4; the EMCS requirements of §
130.5(f); and all other requirements in § 150.0(k)2.
§ 150.0(k)21:
Interior Switches and Controls. A multiscene programmable controller may be used to comply with dimmer requirements in § 150.0(k) if it
provides the functionality of a dimmer according to § 110.9, and complies with all other applicable requirements in § 150.0(k)2.
2016 Low -Rise Residential Mandatory Measures Summary
§ 150.0(k)2J:
Interior Switches and Controls. In bathrooms, garages, laundry rooms, and utility rooms, at least one luminaire in each of these spaces must
be controlled by a vacancy sensor.
§ 150.0(k)2K:
Interior Switches and Controls. Dimmers or vacancy sensors must control all luminaires required to have light sources compliant with
Reference Joint Appendix JAB, except luminaires in closets less than 70 square feet and luminaires in hallways.'
§ 150.0(k)2L:
Interior Switches and Controls. Undercabinet lighting must be switched separately from other lighting systems.
Residential Outdoor Lighting. For single-family residential buildings, outdoor lighting permanently mounted to a residential building, or to other
§ 150.0(k)3A:
buildings on the same lot, must meet the requirement in item § 150.0(k)3Ai (ON and OFF switch) and the requirements in either item
§ 150.0(k)3Aii (photocell and motion sensor) or item § 150.0(k)3Aiii (photo control and automatic time switch control, astronomical time clock, or
EMCS.
Residential Outdoor Lighting. For low-rise multifamily residential buildings, outdoor lighting for private patios, entrances, balconies,
§ 150.0(k)3B:
and porches; and outdoor lighting for residential parking lots and residential carports with less than eight vehicles per site must comply with
either § 150.0(k)3A or with the applicable requirements in §§ 110.9, 130.0, 130.2, 130.4, 140.7 and 141.0.
§ 150.0(k)3C:
Residential Outdoor Lighting. For low-rise residential buildings with four or more dwelling units, outdoor lighting not regulated by
150.0(k)3B or § 150.0(k)3D must comply with the applicable requirements in §§ 110.9, 130.0, 130.2, 130.4, 140.7 and 141.0.
§ 150.0(k)3D:
Residential Outdoor Lighting. Outdoor lighting for residential parking lots and residential carports with a total of eight or more
vehicles per site must comply with the applicable requirements in §§ 110.9, 130.0, 130.2, 130.4, 140.7, and 141.0.
§ 150.0(k)4:
Internally illuminated address signs. Internally illuminated address signs must comply with § 140.8; or must consume no more than 5 watts of
ower as determined according to § 130.0(c).
§ 150.0(k)5:
Residential Garages for Eight or More Vehicles. Lighting for residential parking garages for eight or more vehicles must comply with the
applicable requirements for nonresidential garages in §§ 110.9, 130.0, 130.1, 130.4, 140.6, and 141.0.
Interior Common Areas of Low-rise Multi -Family Residential Buildings. In a low-rise multifamily residential building where the total interior
§ 150.0(k)6A:
common area in a single building equals 20 percent or less of the floor area, permanently installed lighting for the interior common areas in that
building must be high efficacy luminaires and controlled by an occupant sensor.
Interior Common Areas of Low-rise Multi -Family Residential Buildings. In a low-rise multifamily residential building where the total interior
common area in a single building equals more than 20 percent of the floor area, permanently installed lighting in that building must:
§ 150.0(k)6B:
i. Comply with the applicable requirements in §§ 110.9, 130.0, 130.1, 140.6 and 141.0; and
ii. Lighting installed in corridors and stairwells must be controlled by occupant sensors that reduce the lighting power in each space by at least
50 percent. The occupant sensors must be capable of turning the light fully on and off from all designed paths of ingress and egress.
Solar Ready Buildings:
Single Family Residences. Single family residences located in subdivisions with ten or more single family residences and where the
§ 110.10(a)1:
application for a tentative subdivision map for the residences has been deemed complete by the enforcement agency must comply with the
requirements of § 110.10 b through § 110.1Ole).
§ 110.10(a)2:
Low-rise Multi -family Buildings. Low-rise multi -family buildings must comply with the requirements of § 110.10(b) through § 110.10(d).
Minimum Area. The solar zone must have a minimum total area as described below. The solar zone must comply with access, pathway, smoke
ventilation, and spacing requirements as specified in Title 24, Part 9 or other Parts of Title 24 or in any requirements adopted by a local
jurisdiction. The solar zone total area must be comprised of areas that have no dimension less than 5 feet and are no less than 80 square feet
each for buildings with roof areas less than or equal to 10,000 square feet or no less than 160 square feet each for buildings with roof areas
§ 110.10(b)1:
greater than 10,000 square feet.
For single family residences the solar zone must be located on the roof or overhang of the building and have a total area no less than 250
square feet. For low-rise multi -family buildings the solar zone must be located on the roof or overhang of the building, or on the roof or overhang
of another structure located within 250 feet of the building, or on covered parking installed with the building project, and have a total area no less
than 15 percent of the total roof area of the building excluding any skylight area.'
§ 110.10(b)2:
Orientation. All sections of the solar zone located on steep -sloped roofs must be oriented between 110 degrees and 270 degrees of true north.
§ 110.10(b)3A:
Shading. The solar zone must not contain any obstructions, including but not limited to: vents, chimneys, architectural features, and roof
mounted equipment.*
Shading. Any obstruction located on the roof or any other part of the building that projects above a solar zone must be located at least twice the
§ 110.10(b)3B:
distance, measured in the horizontal plane, of the height difference between the highest point of the obstruction and the horizontal projection of
the nearest point of the solar zone, measured in the vertical lane.'
§ 110.10(b)4:
Structural Design Loads on Construction Documents. For areas of the roof designated as solar zone, the structural design loads for roof
dead load and roof live load must be clearly indicated on the construction documents.
Interconnection Pathways. The construction documents must indicate: a location for inverters and metering equipment and a pathway for
§ 110.10(c):
routing of conduit from the solar zone to the point of interconnection with the electrical service (for single family residences the point of
interconnection will be the main service panel); and a pathway for routing of plumbing from the solar zone to the water -heating system.
§ 110.10(d):
Documentation. A copy of the construction documents or a comparable document indicating the information from § 110.10(b) through
1 10.10 c must be provided to the occupant.
§ 110.10(e)1:
Main Electrical Service Panel. The main electrical service panel must have a minimum busbar rating of 200 amps.
Main Electrical Service Panel. The main electrical service panel must have a reserved space to allow for the installation of a double pole circuit
§ 110.10(e)2:
breaker for a future solar electric installation. The reserved space must be: positioned at the opposite (load) end from the input feeder location or
main circuit location; and permanently marked as "For Future Solar Electric".
HVAC SYSTEM HEATING AND COOLING LOADS SUMMARY
Project Name
Boelman Residence
Date
8/7/2017
System Name
HVAC System
Floor Area
1,857
ENGINEERING CHECKS
SYSTEM LOAD
Number of Systems
' 1
COIL
CFM
Total Room Loads 796
Return Vented Lighting
Return Air Ducts
Return Fan
Ventilation 0
Supply Fan
Supply Air Ducts
TOTAL SYSTEM LOAD
COOLING
PEAK COIL HTG.
PEAK
Heating System
Sensible
Latent CFM
Sensible
Output per System 80,000
16,515
404 450
17,550
Total Output Btuh 80,000
0
Output Btuh/s ft 43.1
662
688
Cooling System
0
0
Output per System 1
0
0 0
0
Total Output Btuh 1
0
404
0
Total Output Tons 0.0
662
688
Total Output Btuh/s ft 0.0
Total Output s ft/Ton 22,284,000.0
1 17,839
18,925
Air System
CFM per System
0
HVAC EQUIPMENT SELECTION
Airflow cfm
0
High Efficiency Fau/AC
1
0
80,000
Airflow cfm/s ft
0.00
Airflow cfm/Ton
0.0
Outside Air %
0.0%
Total Adjusted System Output
(Adjusted for Peak Design conditions)
TIME OF SYSTEM PEAK
1 1
0
Aug 3 PM
80,000
Outside Air cfm/s ft 0.00
Note: values above given at ARI conditions
Jan 1 AM
HEATING SYSTEM PSYCHROMETRICS
Airstream Temperatures at Time of Heating
Peak
25 OF
Outside Air
0 cfm
67 OF
67 OF 105 OF
I U I
Heating Coil
I I
fl
104 OF
ROOM
68 OF
COOLING SYSTEM PSYCHROMETRICS Airstream Temperatures at Time of Cooling
Peak
104/70°F
Outside Air
0 cfm
76/61 OF
76/60°F 55/53°F
Cooling Coil
56 / 53 OF
42.4% ROOM
75/60°F
EnergyPro 7.1 by EnergySoft
User Number: 7272
/D: 17-003
Page 16 of 17
,1 •
ZONE LOAD SUMMARY
Project
Boelman Residence
System Name.
HVAC System
Floor Area
1,857
ZONE LOAD SUMMARY
ZONAL SYSTEM COOLING
Energy.. -17-003
Page17of17