The URL can be used to link to this page

Home My WebLink AboutDBP-51 Residential New Manufactured Home ChecklistPage 1 of 2 Butte County Department of Development Services PERMIT CENTER 7 County Center Drive, Oroville, CA 95965 Main Phone (530) 552-3700 Fax (530) 538-7785 www.buttecounty.net/dds New Manufactured Home Plan Submittal Checklist Purpose This handout summarizes the requirements for a complete plan review submittal for a new residential manufactured home. The following guideline shall be reviewed before commencing any work. Note: Manufactured homes cannot be older than 10 years from manufacturer date to permit submittal date. Additional Agency Approvals Planning Contact the Planning Division at (530)552-3701 for land use and setbacks prior to submittal of plans. If located in City of Gridley, contact the City Planning Department at (530) 846-3631 If located in City of Biggs, contact the City Planning Department at (530) 868-5447 Environmental Health Contact the Environmental Health Department for septic or well requirements at (530) 552-3880 or stop by their office located at 202 Mira Loma Dr., Oroville CA 95965. Public Works Contact the Public Works Department for information on encroachment permit requirements or legal lot determination at (530) 538-7681. CAL Fire Contact CAL Fire for requirements at (530) 538-6320 for new construction. Plan Submittal for Construction Quantity Complete plans and documents can be submitted directly to the Building Division counter between 8:00 am to 4:00 pm, Monday through Friday (Wednesdays hours are 8:00 am to 3:00 pm) or by email to dsbuilding@buttecounty.net.  Three (3) complete sets of plans. At least two sets must be signed by their designer.  One (1) Installation manual from the manufacturer.  Two (2) complete foundation or tie down plans, stamped and signed by the licensed professional and/or stamped approved by the State of California.  Two (2) complete Butte County Manufactured Home Support Data Sheets (Form DBP-52).  Two (2) marriage line plan from the manufacturer (If the home is larger than a single wide)  Complete permit application.  Plan check fee payment. Minimum Plan Requirements Size Plans must be drawn to scale, fully dimensioned and legible on minimum 11 x 17 inch paper (e.g., site plan: 1/8-in = 1-ft, floor plan: ¼-in = 1-ft) in a concise, detailed and professional manner. Cover Sheet and / or Site Plan o Job address / name and address of owner, contractor and contact person / address, phone number, title and registration of designer or design professional / description of work / applicable codes / type of construction / fire sprinkler system (yes or no) / sheet index / etc. o Site plan identifying lot and building location / setback dimensions from new construction to all property lines and other existing buildings / location of easements / location of utilities such as electric meter, well/water meter, propane tank/gas meter / north arrow / etc. Plans o Manufacturer’s floor plan identifying room uses and all dimensions of home. o Plans for the landings serving all exterior doors. Details for stairs, handrails, guards, decking material, framing, fasteners, etc. Flood Zone Verification o Complete two elevation certificates if property is within 250 feet of a flood zone. FORM NO DBP-51 Page 2 of 2 Design Criteria Butte County has adopted the following codes and amendments: 2016 California Residential Code (2015 IRC) 2016 California Building Code (2015 IBC) 2016 California Mechanical Code (2015 UMC) 2016 California Electrical Code (2014 NEC) 2016 California Plumbing Code (2015 UPC) 2016 California Fire Code (2015 IFC) Title 25 Wind speed design factor: V3S = 110 mph, exposure based on geographical location Seismic design category: D Snow loads per Title 25 Table 1338-1 Region III: Elevation Roof Live Load 0-2000 ft. 20 psf 2001-3000 ft. 30 psf 3001-4000 ft. 60 psf 4001-5000 ft. 80 psf Over 5000 ft See Design Criteria DPC-5 433A (Permanent Foundation – Real Property) Purpose In order to complete the process of recording a home as Real property with Butte County as well as HCD, the county needs to collect and prepare certain documents with the Recorders Office. Required Documents o A copy of the most current Grant Deed with Legal Description. o If the home is used, a current Title (HCD Title) will be required at time of application. If the home is new, a Manufacturers Certificate of Origin (MCO) is provided upon delivery of the home and must be turned in to the Building Division prior to scheduling a Final inspection. o Once the building permit has passed Final Inspection, the Building Division will record the documents and notify the applicant to provide a check for the amount of $11.00 per section ($11.00 single wide, $22.00 double wide, etc.) made out to HCD. This will be sent in with your application. Plan Check Time Refer to the following link for current plan check times: http://www.buttecounty.net/dds/Building Permit Issuance The following will be required at time of permit issuance: o School District fees. o Proof of current contractor’s license / Worker’s Compensation insurance (for contractors only). o Outstanding building fee payment. One set of approved plans will be returned to the applicant to be maintained at the job site until the final inspection has been made. The Building & Safety Division will keep a second set on file. The third set will be forwarded to the County’s Assessor’s Office. (If submitted digitally, a copy of the approved plans will be emailed to the applicant) Questions Contact the Building Division at (530) 552-3700 for inquiries on plan check and building fees.