Loading...
HomeMy WebLinkAbout49AV DATASHEET (IAUTOCALL TrueAlert ES Addressable Notification Appliances ULC Listed Wall Mount Weatherproof Notification Appliances Visible Only(VO)and Audible/Visible(AN) Features Individually addressed and controlled multi-candela TrueAlert ES / tweatherproof notification appliances for extended temperatureand humidity range provide: gmit• Multi-candela xenon strobe with synchronized 1 Hz flash rate and withum intensity programmable from the control panel or jumper selected as 20,30,or 75 cd Fill F.III •Advanced addressable notification controlled by IDNAC SLCs providing regulated 29 VDC allowing strobes to operate with lower current even under battery backup L______F. • \\\�� �. I__ _ - • Wiring supervision to each appliance allowing"T-tapped"connections for Class B circuits to simplify wiring(Class A circuits require in/out g ' � � —�'aJ�-wirin ) � - • Self-Test Mode allows on board sensors to detect the strobe andshorn output and then report their status to the control panel F E FEU• TrueAlert Device Reports at the control panel detailing appliance --I R f-' - f' point ID,custom label,type,and candela setting(see sample on page 3) Figure 1: Weatherproof A/V(top)and Strobe(bottom), • Magnet Test diagnostics to assist checkout and testing of appliances side view of A/V on Weatherproof Mounting Boxes(right) and wiring For A/V Models with horn: • Electrical test point access without removing cover • Harmonically rich output sound for either coded or steady operation LED Indicator and Magnet Test feature: • Horns sound as Temporal Code 3,March Time pattern,continuous;or •Appliance LED can be selected to display each polling cycle to indicate Temporal Code 4,controlled separately from visible appliances on the appliance supervision • same two-wire circuit • When the controller is in diagnostic mode,the Magnet Test pulses the Selectable March Time rates of 20,60,or 120 beats per minute LED to indicate appliance address and can be set to also briefly flash • Output is"high"or"low"(-5 dBA difference)selectable at the appliance the strobe and sound the AN horn or from the controller with FACP mode selected at the appliance Mechanical design features include: Description • Rugged,high impact,flame retardant thermoplastic housing with clear TrueAlert ES weatherproof addressable appliances provide visible lens and audible/visible notification for indoor and outdoor,extended • Standard models are red and available with FIRE or FEU lettering; temperature and extended humidity applications.They are individually configured models are available with additional lettering of FEU/FIRE, addressed and receive power,supervision,and control signals from a ALERT,and blank,and in white with each lettering Autocall fire alarm control panel providing IDNAC Signaling Line Circuits • Mounting is to matching weatherproof boxes(required),ordered (SLCs).(See compatibility list on page 4.) separately • Separate covers are available to change application type on-site or for Strobe application reference replacement Proper selection of visible notification is dependent on occupancy, • In/out wiring terminals for 18 AWG to 12 AWG location,local codes,and proper applications of:the National Fire Alarm • Enclosure is rated NEMA 3R Code(NFPA 72),ANSI A117.1;the appropriate model building code: • Convenient wiring terminal access at front of housing BOCA,ICBO,or SBCCI;and the application guidelines of the Americans with Disabilities Act(ADA). Agency listings reference: • Strobe operation is listed to ULC-5526 • Horn operation is listed to ULC-5525 • Refer to data sheet A49WP-0001 for UL listed models *Additional listings may be applicable;contact your local product supplier for the latest status. A49WP-0002 Rev.4 6/2019 fiNAUTOCALL Wall Mount Weatherproof Notification Appliances Visible Only(VO)and AudibleNisible(AN) TrueAlert ES operation advantage TrueAlert ES addressable appliances on IDNAC SLCs provide separate visible and audible notification using a single two-wire circuit that also confirms connection to the individual notification appliance's electronic circuit.This operation increases circuit supervision integrity by providing supervision that extends beyond the appliance wiring connections. Reduced current allows efficient IDNAC SLC operation.With IDNAC SLCs,a constant 29 VDC source voltage is maintained,even during battery standby,allowing strobes to operate at higher voltage with lower current and ensuring a consistent current draw and voltage drop margin under both primary power and secondary battery standby.Efficiencies include wiring distances up to 2 to 3 times farther than with conventional notification, or support for more appliances per IDNAC SLC,or use of smaller gauge wiring,or combinations of these benefits,all providing installation and maintenance savings with high assurance that appliances that operate during normal system testing will operate during worst case alarm conditions. Reducing Installation and Testing Time.With separate controls on the same two-wire SLC,installation time and expense for both retrofit and new construction can be significantly reduced.When Class B wiring is used,wiring can be"T"tapped,allowing more savings in distance,wire,conduit(size and utilization),and overall installation efficiency.Use of Self-Test and Magnet Test features improves installation efficiency.TrueAlert device reports conveniently identify information about each connected appliance. TrueAlert ES diagnostics Test Features.When IDNAC SLCs are in diagnostic mode,Self-Test and Magnet Test features provide individual appliance testing.With the Self-Test feature,appliance operation can be confirmed without leaving the control panel.Additionally,each appliance's LED can be selected to pulse when it receives a supervision poi during normal operation. Self-Test Details.Selecting Self-Test Mode from the control panel allows on-board sensors,depending on the device type,to detect its own strobe and/ or horn output and then report their status to the control panel.Operation is by selected VNAC appliance groups and is either automatic(all briefly simultaneously activated)or individually activated by applying a magnet.(Refer to control panel data sheet for more Self-Test information,see list on page 4.) Silent Appliance Magnet Test.In this test mode,in response to application of a magnet,the appliance LED pulses sequentially to conveniently indicate the appliance's address. Operational Appliance Magnet Test.In this test mode,after the address is indicated by pulsing the appliance LED,the strobe will briefly flash and the A/V horn will briefly sound to indicate proper operation. TrueStart Instrument Two(TSIT).The 2nd generation of the Autocall TrueStart Test Instrument adds testing of IDNAC SLC wiring and TrueAlert ES appliances to its ability to test IDCs,NACs,and IDNet communications before connection to the control panel.Please contact your local Autocall representative for additional information. TrueAlert addressable wiring isolator Isolator Model A4905-9929 is available for remote mounting on TrueAlert addressable circuits to isolate short circuited wiring from functioning wiring. Product selection Table 1:ULC listed TrueAlert ES addressable weatherproof notification appliances Type Model Cover color/lettering Description ULC intensity ratings ULC listed weatherproof TrueAlert ES Horn/Strobe(AN) A49AV-APPLW-CO order cover separately addressable appliance;requires weatherproof 20,30,or 75 cd box below Table 2:Separate Covers(Required when ordering A49AV-APPLW-CO) Lettering Red VO cover models Red AV cover models White VO cover models White AV cover models FIRE A49VOC-WRFIRE-O A49AVC-WRFIRE-O A49VOC-WWFIRE-O A49AVC-WWFIRE-O ALERT A49VOC-WRALT-0 A49AVC-WRALT-0 IA49VOC-WWALT-0 IA49AVC-WWALT-0 FEU A49VOC-WRFEU-0 A49AVC-WRFEU-0 IA49VOC-WWFEU-0 IA49AVC-WWFEU-0 FEU/FIRE A49VOC-WRBLNG-0 A49AVC-WRBLNG-0 IA49VOC-WWBLNG-O IA49AVC-WWBLNG-O Blank A49VOC-WRS-0 A49AVC-WRS-0 IA49VOC-WWS-0 IA49AVC-WWS-0 Table 3:Wall mount weatherproof boxes(required) Model Color Description Dimensions A49WPBB-AWOWR Red Surface Mount Weatherproof 5 1/2"H x 6 1/8"W x 1 5/8"D(140 A49WPBB-AWOWW (White Mounting Box(required) mm x 156 mm x 41 mm) Page 2 A49WP-0002 Rev.4 6/2019 ( AUTOCALL Wall Mount Weatherproof Notification Appliances Visible Only(VO)and AudibleNisible(AN) TrueAlert device reports reference Service Port Page 1 REPORT 5 : TrueAlert Device Report 12:34:56am TUE 27-Jan-15 DEVICE POINT ID CUSTOM LABEL TYPE CANDELA T14-1-1 Location Label . . . up to 40 characters V/O 15 T14-1-2 Break Room 5 A/V 110 T14-1-3 Boiler Room A/V 75 T14-1-4 Elec. Room 7 A/V 135 Figure 2: Report example Installation references Cover to mounting box Knockouts top; bottom. sides; and back; 5 total mounting screws(3) ri . Weatherproof mountingbox*(required) Housing (AN shown) 1:,--__ I p { q ) Housing to mounting41v-;mow 1 �* box screws (2) • .4: Perimeter gasket; pre-installed 4W ,---(5) _ I ` Intensity selection plug, accessible : only from rear of housing; factory P. setting is FACP; selected from fire 11 _ .:; I }' 0IFACP alarm control panel '''' —____J Three(3)cover attachment tabs located bottom; left and right side Internal cover gasket Standard cover s pre-installed Strobe intensity viewing slot (A/V shown) Magnet test location (bottom of housing) Figure 3: Weatherproof appliance installation reference *Red:A49WPBB-AWOWR;white:A49WPBB-AWOWW b 5-3/8 in.(137 rnm) IMPORTANT! INDOOR WALL MOUNT 5 3/8 in.(137 mm) MOUNTING HEIGHT REFERENCE rr--- Ir „ 5-17/32 in. LED Indicator (140 mm) FLD total height 7 : 0i t 4-1,2 in. 81 in.(2.06 m) (114 mm) NFPA 72 requires that minimum to AI — the entire lens be not mounting tabs -,� less than 80 in.and F - not greater than 96 in. 71:7 above the finished — — 11.111111.L ', floor I 5-9/16 in.(141 mm) �. 1-21/32 in. between mounting holes �4-11/32 in. (110 mm) total depth (42 mm) 11 1/8 in.(156 mm) Figure 4: Dimension and mounting height reference Page 3 A49WP-0002 Rev.4 6/2019 ( AUTOCALL Wall Mount Weatherproof Notification Appliances Visible Only(VO)and AudibleNisible(AN) Table 4:IDNAC SLC controller compatibility reference Compatible controllers Controller output IDNAC SLC output voltage Appliance voltage design reference 4100ES with EPS+or EPS Power Supply 4009 IDNAC Repeater IDNAC SLC 29 VDC(regulated) 23 VDC(with 6 VDC drop) 4007ES with IDNAC Notification 4010ES with ESS Enhanced System Supply Specifications Table 5:General specifications Specification Rating Typical Operating Voltage Range 23 VDC to 31 VDC,Special Application Supervisory Requirements 1 unit load(=0.8 mA control panel current) IDNAC SLC Loading Maximum of 127 addresses per SLC,139 unit loads Temperature Range -40°F to 150°F(-40°C to 66°C);20,30,or 75 cd setting Humidity Range up to 98%,at 104°F(40°C) IUTP,unshielded twisted pair recommended IDNAC SLC Wiring Specifications(refer to control panel installation Maximum wire length allowed with"T-Taps"for Class B wiring per SLC= instructions for more information) 10,000 ft(3048 m) (Maximum wire length to any appliance=4000 ft(1219 m) Wiring Connections Terminal blocks for 18 AWG to 12 AWG(0.82 mm2 to 3.31 mm2);two wires per terminal for in/out wiring Table 6:AN horn output ratings @ 10 ft(3 m)@ 23 VDC Sound type Anechoic chamber,ULC 525 test Steady/high 87.4 dB Steady/low 181.0 dB* Coded/high 187.2 dB Coded/low 180.6 dB* Note:*Settings with ratings below 85 dB should not be used for Public Notification.Coded values are typical of the output measured with a Temporal coded or a March Time coded pulse and with a sound level meter reading on a"fast"setting. Table 7:23 VDC current ratings Model 20 cd 30 cd 75 cd AN Model A49AV-APPLW-CO,horn 161 mA 165 mA 181 mA on continuous,high setting Level Decrease Horizontal Angle Vertical Angle AN Sound Dispersion per ULC-5525 3 dB 1+50°(to right) I+55°(above axis) Anechoic testing performed at 3 m I-40°(to left) I-70°(below axis) (10 ft);referenced to on-axis=0° -6 dB 1+85°(to right) 1+60°(above axis) 185°(to left) 1-90°(below axis) ©2019 Johnson Controls.All rights reserved.All specifications and other information shown were current as of document revision and are subject to change without notice. Additional listings may be applicable,contact your local Autocall product supplier for the latest status.Listings and approvals under Tyco Fire&Security GmbH,and the product names listed in this material are marks and/or registered marks.Unauthorized use is strictly prohibited.NFPA 72 and National Fire Alarm Code are registered trademarks of the National Fire Protection Association(NFPA). A49 W P-0002 Rev.4 6/2019